• ### Experimental conditions to suppress edge localised modes by magnetic perturbations in the ASDEX Upgrade tokamak(1804.00933)

April 3, 2018 physics.plasm-ph
Access conditions for full suppression of Edge Localised Modes (ELMs) by Magnetic Perturbations (MP) in low density high confinement mode (H-mode) plasmas are studied in the ASDEX Upgrade tokamak. The main empirical requirements for full ELM suppression in our experiments are: 1. The poloidal spectrum of the MP must be aligned for best plasma response from weakly stable kink-modes, which amplify the perturbation, 2. The plasma edge density must be below a critical value, $3.3 \times 10^{19}$~m$^{-3}$. The edge collisionality is in the range $\nu^*_i = 0.15-0.42$ (ions) and $\nu^*_e = 0.15-0.25$ (electrons). However, our data does not show that the edge collisionality is the critical parameter that governs access to ELM suppression. 3. The pedestal pressure must be kept sufficiently low to avoid destabilisation of small ELMs. This requirement implies a systematic reduction of pedestal pressure of typically 30\% compared to unmitigated ELMy H-mode in otherwise similar plasmas. 4. The edge safety factor $q_{95}$ lies within a certain window. Within the range probed so far, $q_{95}=3.5-4.2$, one such window, $q_{95}=3.57-3.95$ has been identified. Within the range of plasma rotation encountered so far, no apparent threshold of plasma rotation for ELM suppression is found. This includes cases with large cross field electron flow in the entire pedestal region, for which two-fluid MHD models predict that the resistive plasma response to the applied MP is shielded.
• ### Three dimensional boundary displacement due to stable ideal kink modes excited by external n=2 magnetic perturbations(1702.03177)

July 24, 2017 physics.plasm-ph
In low-collisionality scenarios exhibiting mitigation of edge localized modes (ELMs), stable ideal kink modes at the edge are excited by externally applied magnetic perturbation (MP)-fields. In ASDEX Upgrade these modes can cause three-dimensional (3D) boundary displacements up to the centimeter range. These displacements have been measured using toroidally localized high resolution diagnostics and rigidly rotating n = 2 MP-fields with various applied poloidal mode spectra. These measurements are compared to non-linear 3D ideal magnetohydrodynamics (MHD) equilibria calculated by VMEC. Comprehensive comparisons have been conducted, which consider for instance plasma movements due to the position control system, attenuation due to internal conductors and changes in the edge pressure profiles. VMEC accurately reproduces the amplitude of the displacement and its dependencies on the applied poloidal mode spectra. Quantitative agreement is found around the low field side (LFS) midplane. The response at the plasma top is qualitatively compared. The measured and predicted displacements at the plasma top maximize when the applied spectra is optimized for ELM-mitigation. The predictions from the vacuum modeling generally fails to describe the displacement at the LFS midplane as well as at the plasma top. When the applied mode spectra is set to maximize the displacement, VMEC and the measurements clearly surpass the predictions from the vacuum modeling by a factor of four. Minor disagreements between VMEC and the measurements are discussed. This study underlines the importance of the stable ideal kink modes at the edge for the 3D boundary displacement in scenarios relevant for ELM-mitigation.
• ### Quiescence near the X-point of MAST measured by high speed visible imaging(1706.06318)

June 20, 2017 physics.plasm-ph
Using high speed imaging of the divertor volume, the region close to the X-point in MAST is shown to be quiescent. This is confirmed by three different analysis techniques and the quiescent X-point region (QXR) spans from the separatrix to the 1.02 flux surface. Local reductions to the atomic density and effects associated with the camera viewing geometry are ruled out as causes of the QXR, leaving quiescence in the local plasma conditions as being the most likely cause. The QXR is found to be ubiquitous across a significant operational space in MAST including L-mode and H-mode discharges across wide ranges of line averaged density, plasma current and NBI power. When mapped to the divertor target the QXR occupies approximately an e-folding length of the heat-flux profile, containing approximately 60% of the total heat flux to the target, and also shows a tendency towards higher frequency shorter lived fluctuations in the ion-saturation current. This is consistent with short- lived divertor localised filamentary structures observed further down the outer divertor leg in the camera images, and suggests a complex multi-region picture of filamentary transport in the divertor.
• ### Plasma response measurements of external magnetic perturbations using electron cyclotron emission and comparisons to 3D ideal MHD equilibrium(1603.09150)

Aug. 4, 2016 physics.plasm-ph
The plasma response from an external n = 2 magnetic perturbation field in ASDEX Upgrade has been measured using mainly electron cyclotron emission (ECE) diagnostics and a rigid rotating field. To interpret ECE and ECE-imaging (ECE-I) measurements accurately, forward modeling of the radiation transport has been combined with ray tracing. The measured data is compared to synthetic ECE data generated from a 3D ideal magnetohydrodynamics (MHD) equilibrium calculated by VMEC. The measured amplitudes of the helical displacement around the low field side midplane are in reasonable agreement with the one from the synthetic VMEC diagnostics. Both exceed the prediction from the vacuum field calculations and indicate the presence of a kink response at the edge, which amplifies the perturbation. VMEC and MARS-F have been used to calculate the properties of this kink mode. The poloidal mode structure of the magnetic perturbation of this kink mode at the edge peaks at poloidal mode numbers larger than the resonant components |m| > |nq|, whereas the poloidal mode structure of its displacement is almost resonant |m| ~ |nq|. This is expected from ideal MHD in the proximity of rational surfaces. The displacement measured by ECE-I confirms this resonant response.
• ### ELM control with RMP: plasma response models and the role of edge peeling response(1607.01161)

July 5, 2016 physics.plasm-ph
Resonant magnetic perturbations (RMP) have extensively been demonstrated as a plausible technique for mitigating or suppressing large edge localized modes (ELMs). Associated with this is a substantial amount of theory and modelling efforts during recent years. Various models describing the plasma response to the RMP fields have been proposed in the literature, and are briefly reviewed in this work. Despite their simplicity, linear response models can provide alternative criteria, than the vacuum field based criteria, for guiding the choice of the coil configurations to achieve the best control of ELMs. The role of the edge peeling response to the RMP fields is illustrated as a key indicator for the ELM mitigation in low collisionality plasmas, in various tokamak devices.
• ### Scrape-off layer ion temperature measurements at the divertor target during type III and type I ELMs in MAST measured by RFEA(1602.03015)

Feb. 9, 2016 physics.plasm-ph
In future nuclear fusion reactors high heat load events, such as edge-localised modes (ELMs), can potentially damage divertor materials and release impurities into the main plasma, limiting plasma performance. The most difficult to handle are type I ELMs since they carry the largest fraction of energy from the plasma and therefore deposit the largest heat flux at the target and on first wall materials. Knowing the temperature of the ions released from ELM events is important since it determines the potential sputtering they would cause from plasma facing materials. To make measurements of Ti by retarding field energy analyser (RFEA) during type I ELMs a new operational technique has been used to allow faster measurements to be made; this is called the fast swept technique (FST).
• ### L-mode filament characteristics on MAST as a function of plasma current measured using visible imaging(1602.03021)

Feb. 9, 2016 physics.plasm-ph
Clear filamentary structures are observed at the edge of tokamak plasmas. These filaments are ejected out radially and carry plasma in the far Scrape Off Layer (SOL) region, where they are responsible for producing most of the transport. A study has been performed of the characteristics of the filaments observed in L-mode plasma on MAST, using visible imaging. A comparison has then been made with the observed particle and power profiles obtained at the divertor as a function of the plasma current. The radial velocity and to a lesser extent the radial size of the filaments are found to decrease as the plasma current is increased at constant density and input power. The results obtained in this paper on the dependence of the average filament dynamics on plasma current are consistent with the idea that the filaments are responsible for determining the particle profiles at the divertor.
• This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C. Please note that version 3 on the archive is the auxiliary version of the Physics of the B Factories book. This uses the notation alpha, beta, gamma for the angles of the Unitarity Triangle. The nominal version uses the notation phi_1, phi_2 and phi_3. Please cite this work as Eur. Phys. J. C74 (2014) 3026.
• ### Characterisation of the L-mode Scrape Off Layer in MAST: decay lengths(1506.04530)

June 15, 2015 physics.plasm-ph
This work presents a detailed characterisation of the MAST Scrape Off Layer in L-mode. Scans in line averaged density, plasma current and toroidal magnetic field were performed. A comprehensive and integrated study of the SOL was allowed by the use of a wide range of diagnostics. In agreement with previous results, an increase of the line averaged density induced a broadening of the midplane density profile.
• ### Nuclear Fusion: Bringing a star down to Earth(1503.08981)

March 31, 2015 physics.plasm-ph
Nuclear fusion offers the potential for being a near limitless energy source by fusing together deuterium and tritium nuclei to form helium inside a plasma burning at 100 million kelvin. However, scientific and engineering challenges remain. This paper describes how such a plasma can be confined on Earth and discusses the similarities and differences with fusion in stars. It focusses on the magnetic confinement technique and, in particular, the method used in a tokamak. The confinement achieved in the equilibrium state is reviewed and it is shown how the confinement can be too good, leading to explosive instabilities at the plasma edge called Edge Localised modes (ELMs). It is shown how the impact of ELMs can be minimised by the application of magnetic perturbations and discusses the physics behind the penetration of these perturbations into what is ideally a perfect conducting plasma.
• ### Interpretation of Scalar and axial mesons in LHCb from an historical perspective(1503.06942)

March 24, 2015 hep-ph, hep-ex
LHCb measurements of $B_{d,s} \to J/\psi + X$ are shown to be consistent with historical data on scalar and axial mesons below 2 GeV. This is in contrast to some recent interpretations of these data. Further tests of our hypotheses in other $B_{u,d,s} \to J/\psi + X$ decay modes are suggested.
• ### Effect of resonant magnetic perturbations on low collisionality discharges in MAST and a comparison with ASDEX Upgrade(1412.7631)

Dec. 24, 2014 physics.plasm-ph
Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedestal height and confined energy. While the applied resonant magnetic perturbation field can be a good indicator for the onset of ELM mitigation on MAST and AUG there are some cases where this is not the case and which clearly emphasise the need to take into account the plasma response to the applied perturbations. The plasma response calculations show that the increase in ELM frequency is correlated with the size of the edge peeling-tearing like response of the plasma and the distortions of the plasma boundary in the X-point region.
• ### Impact of Resonant Magnetic Perturbations on the L-H Transition on MAST(1412.3997)

Dec. 12, 2014 physics.plasm-ph
The impact of resonant magnetic perturbations (RMPs) on the power required to access H-mode is examined experimentally on MAST. Applying RMP in n=2,3,4 and 6 configurations causes significant delays to the timing of the L-H transition at low applied fields and prevents the transition at high fields. The experiment was primarily performed at RMP fields sufficient to cause moderate increases in ELM frequency, f mitigated/f natural~3. To obtain H-mode with RMPs at this field, an increase of injected beam power is required of at least 50% for n=3 and n=4 RMP and 100% for n=6 RMP. In terms of power threshold, this corresponds to increases of at least 20% for n=3 and n=4 RMPs and 60% for n=6 RMPs. This 'RMP affected' power threshold is found to increase with RMP magnitude above a certain minimum perturbed field, below which there is no impact on the power threshold. Extrapolations from these results indicate large increases in the L-H power threshold will be required for discharges requiring large mitigated ELM frequency.
• ### Profile measurements in the plasma edge of MAST using a ball pen probe(1411.7298)

Nov. 26, 2014 physics.plasm-ph
The ball pen probe (BPP) technique is used successfully to make profile measurements of plasma potential, electron temperature and radial electric field on the Mega Amp Spherical Tokamak (MAST). The potential profile measured by the BPP is shown to significantly differ from the floating potential both in polarity and profile shape. By combining the BPP potential and the floating potential the electron temperature can be measured, which is compared with the Thomson scattering (TS) diagnostic. Excellent agreement between the two diagnostics is obtained when secondary electron emission is accounted for in the floating potential. From the BPP profile an estimate of the radial electric field is extracted which is shown to be of the order ~1kV/m and increases with plasma current. Corrections to the BPP measurement, constrained by the TS comparison, introduce uncertainty into the ER measurements. The uncertainty is most significant in the electric field well inside the separatrix. The electric field is used to estimate toroidal and poloidal rotation velocities from ExB motion. This paper further demonstrates the ability of the ball pen probe to make valuable and important measurements in the boundary plasma of a tokamak.
• ### ELM mitigation via rotating resonant magnetic perturbations on MAST(1410.2473)

Oct. 9, 2014 physics.plasm-ph
The application of resonant magnetic perturbations (RMPs) produces splitting of the divertor strike point due to the interaction of the RMP field and the plasma field. The application of a rotating RMP field causes the strike point splitting to rotate, distributing the particle and heat flux evenly over the divertor. The RMP coils in MAST have been used to generate a rotating perturbation with a toroidal mode number n=3. The ELM frequency is doubled with the application of the RMP rotating field, whilst maintaining the H mode. During mitigation, the ELM peak heat flux is seen to be reduced by 50% for a halving in the ELM energy and motion of the strike point, consistent with the rotation of the applied RMP field, is seen using high spatial resolution (1.5mm at the target) heat flux profiles measured using infrared (IR) thermography.
• ### Scaling of the scrape-off layer width during inter-ELM H modes on MAST as measured by infrared thermography(1406.2898)

June 11, 2014 physics.plasm-ph
The power load to the divertor surfaces is a key concern for future devices such as ITER, due to the thermal limits on the material surface. One factor that characterizes the heat flux to the divertor is the fall off length in the scrape-off layer (SOL), which recent empirical scalings have shown could be as small as 1 mm. These predictions are based on a multi-machine scaling of the heat flux width fitted using an expression for the divertor heat flux profile which includes a term for the exponential decay in the SOL and diffusion about the last closed flux surface (LCFS) in the private flux region.
• ### The effect of resonant magnetic perturbations on the divertor heat and particle fluxes in MAST(1307.2485)

June 11, 2014 physics.plasm-ph
Edge localised modes (ELMs) are a concern for future devices, such as ITER, due to the large transient heat loads they generate on the divertor surfaces which could limit the operational time of the device. This paper discusses the application of resonant magnetic perturbations (RMPs) as a mechanism for ELM control on MAST. Experiments have been performed using an n=3 toroidal mode number perturbation and measurements of the strike point splitting performed. The measurements have been made using both infrared and visible imaging to measure the heat and particle flux to the divertor. The measured profiles have shown clear splitting in L-mode which compares well with the predication of the splitting location from modelling including the effect of screening. The splitting of the strike point has also been studied as a function of time during the ELM. The splitting varies during the ELM, being the strongest at the time of the peak heat flux and becoming more filamentary at the end of the ELM (200 microseconds after the peak midplane D(alpha) emission). Variation in the splitting profiles has also been seen, with some ELMs showing clear splitting and others no splitting. A possible explanation of this effect is proposed, and supported by modelling, which concerns the relative phase between the RMP field and the ELM filament location.
• ### Measurement, correction and implications of the intrinsic error fields on MAST(1312.6507)

Dec. 23, 2013 physics.plasm-ph
The misalignment of field coils in tokamaks can lead to toroidal asymmetries in the magnetic field, which are known as intrinsic error fields. These error fields often lead to the formation of locked modes in the plasma, which limit the lowest density that is achievable. The intrinsic error fields on MAST have been determined by the direct measurement of the toroidal asymmetry of the fields from these coils and have been parameterised in terms of distortions to the coils. The error fields are corrected using error field correction coils, where the optimum correction is found by determining the current required to ensure that the discharge is furthest from the onset of a locked mode. These empirically derived corrections have been compared with the known coil distortions. In the vacuum approximation there is a factor of ~ 3 difference between the predicted and empirically determined correction. When the plasma response is included better agreement is obtained, but there are still some cases where the agreement is not good, which suggests that other effects such as the non-linear coupling of the error field to the plasma are important.
• ### Current understanding of the processes underlying the triggering of and energy loss associated with type I ELMs(1312.4300)

Dec. 16, 2013 physics.plasm-ph
The type I ELMy H-mode is the baseline operating scenario for ITER. While it is known that the type I ELM ultimately results from the peeling-ballooning instability, there is growing experimental evidence that a mode grows up before the ELM crash that may modify the edge plasma, which then leads to the ELM event due to the peeling-ballooning mode. The triggered mode results in the release of a large number of particles and energy from the core plasma but the precise mechanism by which these losses occur is still not fully understood and hence makes predictions for future devices uncertain. Our current understanding of the processes that trigger type I ELMs and the size of the resultant energy loss are reviewed and compared to experimental data and ideas for further development are discussed.
• ### Scrape-off layer ion temperature measurements at the divertor target in MAST by retarding field energy analyser(1307.1563)

July 5, 2013 physics.plasm-ph
Knowledge of the ion temperature (Ti) is of key importance for determining heat fluxes to the divertor and plasma facing components, however data regarding this is limited compared to electron temperature (Te) data. Ti measurements at the divertor target, between edge-localised modes (inter-ELM) H-mode, have been made using a novel retarding field energy analyser (RFEA).
• ### Characteristics of X-point Lobe Structures in Single-Null Discharges on MAST(1307.1573)

July 5, 2013 physics.plasm-ph
Lobe structures due to the application of resonant magnetic perturbations (RMPs) have been observed using wide-angle imaging of light from He1+ ions in the vicinity of the lower X-point in MAST. The data presented are from lower single-null discharges where RMPs of toroidal mode number, n, of 4 and 6 were applied. It has been found that, above a threshold value, the lobe structures extend radially, linearly with the coil current, both in L-mode and H-mode. It is observed that after the application of the RMP, as the toroidal rotation in the confined plasma decreases, the lobes extend radially, suggesting the plasma is less effectively screening the RMP field. Comparing the imaging data with results from vacuum modelling shows that this technique can accurately predict the number and poloidal location of the lobes, but over-estimates their radial extent. More accurate estimates of the extent of the lobes can be made by accounting for plasma screening of the RMP field. Qualitative agreement between simulation and experiment is found if it is assumed that the RMP penetrates 2% in normalised radius from the last closed flux surface.
• ### Measurement and control of the fast ion redistribution on MAST(1307.0355)

July 1, 2013 physics.plasm-ph
Previous experiments on MAST and other tokamaks have indicated that the level of fast ion redistribution can exceed that expected from classical diffusion and that this level increases with beam power. In this paper we present a quantification of this effect in MAST plasmas using a recently commissioned scanning neutron camera. The observed fast ion diffusivity correlates with the amplitude of n=1 energetic particle modes, indicating that they are the probable cause of the non-classical fast ion diffusion in MAST. Finally, it will be shown that broadening the fast ion pressure profile by the application of neutral beam injection at an off-axis location can mitigate the growth of these modes and result in the classical fast ion behaviour
• ### MAST-Upgrade Divertor Facility and Assessing Performance of Long-Legged Divertors(1306.6774)

June 28, 2013 physics.plasm-ph
A potentially important feature in a divertor design for a high-power tokamak is an extended and expanded divertor leg. The upgrade to MAST will allow a wide range of such divertor leg geometries to be produced, and hence will allow the roles of greatly increased connection length and flux expansion to be experimentally tested. This will include testing the potential of the Super-X configuration [1]. The design process for the upgrade has required analysis of producing and controlling the magnetic configurations, and has included consideration of the roles that divertor closure and increasing magnetic connection length will play.
• ### L-Mode and Inter-ELM Divertor Particle and Heat Flux Width Scaling on MAST(1306.6777)

June 28, 2013 physics.plasm-ph
The distribution of particles and power to plasma-facing components is of key importance in the design of next-generation fusion devices. Power and particle decay lengths have been measured in a number of MAST L-mode and H-mode discharges in order to determine their parametric dependencies, by fitting power and particle flux profiles measured by divertor Langmuir probes, to a convolution of an exponential decay and a Gaussian function. In all discharges analysed, it is found that exponential decay lengths mapped to the midplane are mostly dependent on separatrix electron density and plasma current (or parallel connection length). The widths of the convolved Gaussian functions have been used to derive an approximate diffusion coefficient, which is found to vary from 1m2/s to 7m2/s, and is systematically lower in H-mode compared with L-mode.
• ### Understanding the effect resonant magnetic perturbations have on ELMs(1306.6841)

June 28, 2013 physics.plasm-ph
All current estimations of the energy released by type I ELMs indicate that, in order to ensure an adequate lifetime of the divertor targets on ITER, a mechanism is required to decrease the amount of energy released by an ELM, or to eliminate ELMs altogether. One such amelioration mechanism relies on perturbing the magnetic field in the edge plasma region, either leading to more frequent, smaller ELMs (ELM mitigation) or ELM suppression. This technique of Resonant Magnetic Perturbations (RMPs) has been employed to suppress type I ELMs at high collisionality/density on DIII-D, ASDEX Upgrade, KSTAR and JET and at low collisionality on DIII-D. At ITER-like collisionality the RMPs enhance the transport of particles or energy and keep the edge pressure gradient below the 2D linear ideal MHD critical value that would trigger an ELM, whereas at high collisionality/density the type I ELMs are replaced by small type II ELMs. Although ELM suppression only occurs within limitied operational ranges, ELM mitigation is much more easily achieved. The exact parameters that determine the onset of ELM suppression are unknown but in all cases the magnetic perturbations produce 3D distortions to the plasma and enhanced particle transport. The incorporation of these 3D effects in codes will be essential in order to make quantitative predictions for future devices.