• We comparatively studied the critical current density, magnetization and specific heat of the rolled and the hot-pressed Sr1-xKxFe2As2 tapes. The Schottky anomaly that is obvious in the specific heat of the rolled tape disappears in the hot-pressed tape. Moreover, the hot-pressed tape has a higher fraction of superconductivity and a narrower distribution of superconducting transition temperature than the rolled tape. Combined with the magnetization data, we conclude that sintering under high pressure provides a better environment for complete chemical reaction and more homogenous dopant distribution, which is beneficial to the global current of a superconductor.
  • The high upper critical field and low anisotropy of iron-based superconductors make them being particularly attractive for high-field applications. However, the current carrying capability needs to be enhanced by overcoming the weak-link effect between misaligned grains inside wire and tape conductors. Here we demonstrate a high transport critical current density (Jc) reaching 1.5x10^5 A/cm^2 (Ic = 437 A) at 4.2 K and 10 T in Ba0.6K0.4Fe2As2 (Ba-122) tapes prepared by a combination of conventional powder-in-tube method and optimized hot-press technique. The transport Jc measured at 4.2 K under high magnetic fields of 27 T is still on the level of 5.5x10^4 A/cm^2, which is much higher than those of low-temperature superconductors. This is the first report of hot-pressed Ba-122 superconducting tapes and these Jc values are by far the highest ever reported for iron-based superconducting wires and tapes. These high-performance tapes exhibit high degree of c-axis texture of Ba-122 grains and low anisotropy of transport Jc, showing great potential for construction of high-field superconducting magnets.
  • Iron-pnictides are hotly studied since 2008 in the superconducting materials research area, due to their special properties and unclear mechanism. Big achievement has been made in the pnictide research during the past years. For practical uses, pnictide superconductor should be fabricated in a long wire form which can be used for different devices. In this work, 100 m class 7-core Sr0.6K0.4Fe2As2 (Sr122) tapes have been made using the powder-in-tube technique, which is reported for the first time. Clearly, an average Jc of 1.3x10^4 A/cm^2 at 10 T was reached over the 115 meter length, showing a high property and good uniformity of 100 meter level Sr122 tapes. Using the 10 m long Sr122 tapes, two double-pancake coils were fabricated by a wind and reaction technique. No transport current could be measured for the coil made from the mono-filamentary tape. However, transport Ic was obtained in the coil made from the 7-filamentary tape. The factors which affect the superconducting property of the coil were discussed in this work.
  • We have studied vortex pinning and dynamics in a Sr0.6K0.4Fe2As2 superconducting tape with critical current density Jc~0.1 MA/cm2 at 4.2 K and 10 T. It is found that grain boundary pinning is dominant in the vortex pinning mechanism. Furthermore, we observe large density of dislocations which can also serve as effective pinning centers. We find that the temperature dependence of critical current density is in agreement with the model of vortices pinned via spatial fluctuation of charge carrier mean free path. Magnetic relaxation measurement indicates that the magnetization depends on time in a logarithmic way. The relaxation rate in the low and intermediate temperature region is small, and it exhibits a weak temperature and field dependence. A crossover from elastic creep to plastic creep regime is observed. Finally, we conclude a vortex phase diagram for the high performance Sr0.6K0.4Fe2As2 superconducting tape.
  • Iron-based superconductors have been considered to be very promising in high-field applications, for which multifilamentary wire and tape conductors with high mechanical strength are essential. In this work, 7-,19- and 114-filament Sr0.6K0.4Fe2As2 (Sr-122) superconducting wires and tapes with silver as matrix and iron as outer reinforcing sheath were produced by the ex situ powder-in-tube method. The mass densities of Sr-122 phase in 7- and 19-filament conductors were investigated by microhardness characterization, which revealed a positive correlation between hardness and transport critical current density (Jc) in round wires and flat tapes with various thicknesses. For Sr-122/Ag/Fe 114-filament conductors, in which an average cross-sectional filament size smaller than 50 microns was achieved by drawing into round wires of 2.0 mm in diameter, the transport Jc can be significantly enhanced by flat rolling, as for the 7- and 19-filament conductors. The highest transport Jc of the 7-,19- and 114-filament Sr-122/Ag/Fe tapes reached 1.4x10^4, 8.4x10^3 and 6.3x10^3 A cm-2 (4.2 K, 10 T), respectively, showing a Jc degradation with the increase of filament number. This Jc degradation can be ascribed to the sausage effect for filaments in longitudinal direction and the grain refinement in these very fine filaments.
  • After our first discovery of superconductivity (SC) with $T_C$=3.7 K in TlNi$_2$Se$_2$, we grew successfully a series of TlNi$_2$Se$_{2-x}$S$_x$ (0.0 $\leq$ x $\leq$2.0) single crystals. The measurements of resistivity, susceptibility and specific heat were carried out. We found that SC with $T_C$=2.3 K also emerges in TlNi$_2$S$_2$ crystal, which appears to involve heavy electrons with an effective mass $m^*$=13$\sim$25 $m_b$, as inferred from the normal state electronic specific heat and the upper critical field, $H_{C2}(T)$. It was found that the $T_C$ and superconducting volume fraction in TlNi$_2$Se$_{2-x}$S$_x$ crystals changes with the disorder degree induced by the partial substitution of S for Se, which is characterized by the residual resistivity ratio (\textit{RRR}). The effect of the disorder on SC may provide some information for understanding the mechanism of SC in this new Ni-chalcogenide system.
  • Copper sheath is the first choice for manufacturing high-Tc superconducting wires and tapes because of its high electrical and thermal conductivities, low cost and good mechanical properties. However, Cu can easily react with superconducting cores, such as BSCCO, MgB2 and pnictides, during high-temperature sintering process and therefore drastically decrease the transport Jc. Here, we report the fabrication of Cu-sheathed Sr1-xKxFe2As2 tapes with superior Jc performance using a simple hot pressing method that is capable of eliminating the lengthy high-temperature sintering required by conventional process. We obtained high-quality Sr1-xKxFe2As2 tapes with processing at 800oC for 30 minutes and measured high Tc and sharp transition. This rapid fabrication method can effectively thwart the diffusion of Cu into polycrystalline Sr-122 core. As a consequence, we achieved high transport Jc of 3.1x10^4 A/cm^2 in 10 T and 2.7x10^4 A/cm^2 in 14 T at 4.2 K. The in-field Jc performance is by far the highest reported for Cu-sheathed high-Tc conductors. Our results demonstrate the potential of Cu sheath for practical application of pnictide wires and tapes.
  • High-performance Sr0.6K0.4Fe2As2 (Sr-122) tapes have been successfully fabricated using hot pressing (HP) process. The effect of HP temperatures (850-925 C) on the c-axis texture, resistivity, Vickers micro-hardness, microstructure and critical current properties has been systematically studied. Taking advantage of high degree of c-axis texture, well grain connectivity and and large concentration of strong-pinning defects, we are able to obtain an excellent Jc of 1.2x10^5 A/cm^2 at 4.2 K and 10 T for Sr-122 tapes. More importantly, the field dependence of Jc turns out to be very weak, such that in 14 T the Jc remains ~1.0x10^5 A/cm^2. These Jc values are the highest ever reported so far for iron-pnictide wires and tapes, achieving the level desired for practical applications. Our results clearly strengthen the position of iron-pnictide conductors as a competitor to the conventional and MgB2 superconductors for high field applications.
  • The industrial manufacturing of the long-length iron-pnictide wires and tapes requires simple and low-cost technology. Although the transport critical current density of the FeAs-122 tapes has already achieved the practical application level, their fabrication procedures are relatively complicated or required specialized instruments. Ag-sheathed Ba0.6K0.4Fe2As2 superconducting tapes were fabricated by the scalable rolling process. At 4.2 K and 10 T, the critical current density Jc has achieved 5.4x10^4 A/cm2. We ascribe the excellent performance to the high purity and homogeneity of the superconducting phase, high density and high c-axis texture of the superconducting core. Our method provides a simple way to scale up the production of the long-length iron-based superconducting tapes with high Jc.
  • SmFeAsO1-xFx (Sm1111) tapes were prepared by an ex-situ powder-in-tube method with a Sn-presintering process. Scanning electron microscopy revealed apparent difference in microstructure between Sn-presintered tapes and the previously reported polycrystalline Sm1111 bulk, since Sn has reduced FeAs wetting phase and filled the voids between Sm1111 grains. The Sn-presintered tapes showed significant enhanced field dependences of transport Jc compared with Sn-added tapes. A highest transport critical current density (Jc) of 3.45x10^4 A cm-2 at 4.2 K and self-field is achieved. Magneto-optical (MO) imaging further confirmed large and well-distributed global and intergranular Jc in Sn-presintered Sm1111 tapes.
  • 122 type pnictide superconductors are of particular interest for high-field applications because of their large upper critical fields Hc2 (> 100 T), low Hc2 anisotropy r (< 2), and high thin-film critical current densities Jc (> 1 MA/cm2 at 4.2 K). Successful magnet applications require fabrication of polycrystalline superconducting wires that exhibit large in-field Jc, which is limited by poor grain coupling and weak-link behavior at grain boundaries. Here we report our recent achievement in the developing Sr0.6K0.4Fe2As2 tapes with transport Jc up to 0.1 MA/cm2 at 10 T and 4.2 K. This value is by far the highest ever recorded for iron based superconducting wires and has surpassed the threshold for practical application for the first time. The synergy effects of enhanced grain connectivity, alleviation of the weak-link behavior at grain boundaries, and the strong intrinsic pinning characteristics led to the superior Jc performance exhibited in our samples. This advanced Jc result opens up the possibility for iron-pnictide superconducting wires to win the race in high-field magnet applications.
  • Iron-chalcogenide compounds with FeSe(Te, S) layers did not attract much attention until the discovery of high-Tc superconductivity (SC) in the iron-pnictide compounds at the begining of 2008. Compared with FeAs-based superconductors, iron-chalcogenide superconductors have aroused enormous enthusiasm to study the relationship between SC and magnetisms with several distinct features, such as different antiferromagnetic ground states with relatively large moments in the parents, indicating possibly different superconducting mechanisms, the existence of the excess Fe atoms or Fe vacancies in the crystal lattice. Another reason is that the large single crystals are easily grown for the iron-chalcogenide compounds. This review will focus on our exploration for the iron-chalcogenide superconductors and discussion on several issues, including the crystal structure, magnetic properties, superconductivity, and phase separation. Some of them reach a consensus but some important questions still remain to be answered.
  • Superconductivity has been first observed in TlNi$_2$Se$_2$ at T$_C$=3.7 K and appears to involve heavy electrons with an effective mass $m^*$=14$\sim$20 $m_b$, as inferred from the normal state electronic specific heat and the upper critical field, H_${C2}$(T). Although the zero-field electronic specific heat data, $C_{es}(T)$, in low temperatures (T < 1/4 T$_C$) can be fitted with a gap BCS model, indicating that TlNi$_2$Se$_2$ is a fully gapped superconductor, the two-gap BCS model presents the best fit to all the $C_{es}(T)$ data below $T_C$. It is also found that the electronic specific heat coefficient in the mixed state, $\gamma_N(H)$, exhibits a \textit{H}$^{1/2}$ behavior, which was also observed in some \textit{s}-wave superconductors, although once considered as a common feature of the \textit{d}-wave superconductors. Anyway, these results indicate that TlNi$_2$Se$_2$, as a non-magnetic analogue of TlFe$_x$Se$_2$ superconductor, is a multiband superconductor of heavy electron system.
  • High resolution angle-resolved photoemission measurements have been carried out to study the electronic structure and superconducting gap of the (Tl$_{0.58}$Rb$_{0.42}$)Fe$_{1.72}$Se$_2$ superconductor with a T$_c$=32 K. The Fermi surface topology consists of two electron-like Fermi surface sheets around $\Gamma$ point which is distinct from that in all other iron-based compounds reported so far. The Fermi surface around the M point shows a nearly isotropic superconducting gap of $\sim$12 meV. The large Fermi surface near the $\Gamma$ point also shows a nearly isotropic superconducting gap of $\sim$15 meV while no superconducting gap opening is clearly observed for the inner tiny Fermi surface. Our observed new Fermi surface topology and its associated superconducting gap will provide key insights and constraints in understanding superconductivity mechanism in the iron-based superconductors.
  • Up to now, there have been two material families, the cuprates and the iron-based compounds with high-temperature superconductivity (HTSC). An essential open question is whether the two classes of materials share the same essential physics. In both, superconductivity (SC) emerges when an antiferromagnetical (AFM) ordered phase is suppressed. However, in cuprates, the repulsive interaction among the electrons is so strong that the parent compounds are "Mott insulators." By contrast, all iron-based parents are metallic. One perspective is that the iron-based parents are weakly correlated and that the AFM arises from a strong "nesting" of the Fermi surfaces. An alternative view is that the electronic correlations in the parents are still sufficiently strong to place the system close to the boundary between itinerancy and electronic localization. A key strategy to differentiate theses views is to explore whether the iron-based system can be tuned into a Mott insulator. Here we identify an insulating AFM in (Tl,K)FexSe2 by introducing Fe-vacancies and creating superconductivity in the Fe-planar. With the increasing Fe-content, the AFM order is reduced. When the magnetism is eliminated, a superconducting phase with Tc as high as 31K (and a Tc onset as high as 40K) is induced. Our findings indicate that the correlation effect plays a crucial role in the iron-based superconductors. (Tl,K)FexSe2, therefore, represents the first Fe-based high temperature superconductor near an insulating AFM.
  • The spin-fluctuation effect in the Se-substituted system Fe$_{1+\delta}$Te$_{1-x}$Se$_x$ ($x$ = 0, 0.05, 0.12, 0.20, 0.28, 0.33, 0.45, 0.48 and 1.00; $0<\delta < 0.12$) has been studied by the measurements of the X-ray diffraction, the magnetic susceptibility under high magnetic fields and the electrical resistivity under magnetic fields up to 14 T. The samples with $x$ = 0.05, 0.12, 0.20, 0.28, 0.33, 0.45 and 0.48 show superconducting transition temperatures in the ranger of 10 K$\sim$14 K. We obtained their intrinsic susceptibilities by the Honda-Owen method. A nearly linear-in-$T$ behavior in magnetic susceptibility of superconducting samples was observed, indicating the antiferromagnetic spin fluctuations have a strong link with the superconductivity in this series. The upper critical field $\mu_0H_{c2}^{orb}$ for $T\to$ 0 was estimated to exceed the Pauli paramagnetic limit. The Kadowaki-Woods and Wilson ratios indicate that electrons are strongly correlated in this system. Furthermore, the superconducting coherence length and the electron mean free path were also discussed. These superconducting parameters indicate that the superconductivity in the Fe$_{1+\delta}$Te$_{1-x}$Se$_x$ system is unconventional.