• ### First results of the CALICE SDHCAL technological prototype(1602.02276)

March 20, 2016 hep-ex, physics.ins-det
The CALICE Semi-Digital Hadronic Calorimeter (SDHCAL) prototype, built in 2011, was exposed to beams of hadrons, electrons and muons in two short periods in 2012 on two different beam lines of the CERN SPS. The prototype with its 48 active layers, made of Glass Resistive Plate Chambers and their embedded readout electronics, was run in triggerless and power-pulsing mode. The performance of the SDHCAL during the test beam was found to be very satisfactory with an efficiency exceeding 90% for almost all of the 48 active layers. A linear response (within 5%) and a good energy resolution are obtained for a large range of hadronic energies (5-80GeV) by applying appropriate calibration coefficients to the collected data for both the Digital (Binary) and the Semi-Digital (Multi-threshold) modes of the SDHCAL prototype. The Semi-Digital mode shows better performance at energies exceeding 30GeV
• ### Hadron shower decomposition in the highly granular CALICE analogue hadron calorimeter(1602.08578)

March 15, 2016 physics.ins-det
The spatial development of hadronic showers in the CALICE scintillator-steel analogue hadron calorimeter is studied using test beam data collected at CERN and FNAL for single positive pions and protons with initial momenta in the range from 10 to 80 GeV/c. Both longitudinal and radial development of hadron showers are parametrised with two-component functions. The parametrisation is fit to test beam data and simulations using the QGSP_BERT and FTFP_BERT physics lists from Geant4 version 9.6. The parameters extracted from data and simulated samples are compared for the two types of hadrons. The response to pions and the ratio of the non-electromagnetic to the electromagnetic calorimeter response, h/e, are estimated using the extrapolation and decomposition of the longitudinal profiles.
• ### DHCAL with Minimal Absorber: Measurements with Positrons(1603.01652)

March 4, 2016 physics.ins-det
In special tests, the active layers of the CALICE Digital Hadron Calorimeter prototype, the DHCAL, were exposed to low energy particle beams, without being interleaved by absorber plates. The thickness of each layer corresponded approximately to 0.29 radiation lengths or 0.034 nuclear interaction lengths, defined mostly by the copper and steel skins of the detector cassettes. This paper reports on measurements performed with this device in the Fermilab test beam with positrons in the energy range of 1 to 10 GeV. The measurements are compared to simulations based on GEANT4 and a standalone program to emulate the detailed response of the active elements.
• ### Design, Construction and Commissioning of the Digital Hadron Calorimeter - DHCAL(1603.01653)

March 4, 2016 physics.ins-det
A novel hadron calorimeter is being developed for future lepton colliding beam detectors. The calorimeter is optimized for the application of Particle Flow Algorithms (PFAs) to the measurement of hadronic jets and features a very finely segmented readout with 1 x 1 cm2 cells. The active media of the calorimeter are Resistive Plate Chambers (RPCs) with a digital, i.e. one-bit, readout. To first order the energy of incident particles in this calorimeter is reconstructed as being proportional to the number of pads with a signal over a given threshold. A large-scale prototype calorimeter with approximately 500,000 readout channels has been built and underwent extensive testing in the Fermilab and CERN test beams. This paper reports on the design, construction, and commissioning of this prototype calorimeter.
• ### Design, Construction and Testing of the Digital Hadron Calorimeter (DHCAL) Electronics(1603.01654)

March 4, 2016 physics.ins-det
A novel hadron calorimeter is being developed for future lepton colliding beam detectors. The calorimeter is optimized for the application of Particle Flow Algorithms (PFAs) to the measurement of hadronic jets and features a very finely segmented readout with 1 x 1 cm2 cells. The active media of the calorimeter are Resistive Plate Chambers (RPCs) with a digital, i.e. one-bit, readout. To first order the energy of incident particles in this calorimeter is reconstructed as being proportional to the number of pads with a signal over a given threshold. A large-scale prototype calorimeter with approximately 500,000 readout channels has been built and underwent extensive testing in the Fermilab and CERN test beams. This paper reports on the design, construction, and commissioning of the electronic readout system of this prototype calorimeter. The system is based on the DCAL front-end chip and a VME-based back-end.
• ### Pion and proton showers in the CALICE scintillator-steel analogue hadron calorimeter(1412.2653)

March 15, 2015 hep-ex, physics.ins-det
Showers produced by positive hadrons in the highly granular CALICE scintillator-steel analogue hadron calorimeter were studied. The experimental data were collected at CERN and FNAL for single particles with initial momenta from 10 to 80 GeV/c. The calorimeter response and resolution and spatial characteristics of shower development for proton- and pion-induced showers for test beam data and simulations using Geant4 version 9.6 are compared.
• ### The Time Structure of Hadronic Showers in highly granular Calorimeters with Tungsten and Steel Absorbers(1404.6454)

July 21, 2014 hep-ex, physics.ins-det
The intrinsic time structure of hadronic showers influences the timing capability and the required integration time of hadronic calorimeters in particle physics experiments, and depends on the active medium and on the absorber of the calorimeter. With the CALICE T3B experiment, a setup of 15 small plastic scintillator tiles read out with Silicon Photomultipliers, the time structure of showers is measured on a statistical basis with high spatial and temporal resolution in sampling calorimeters with tungsten and steel absorbers. The results are compared to GEANT4 (version 9.4 patch 03) simulations with different hadronic physics models. These comparisons demonstrate the importance of using high precision treatment of low-energy neutrons for tungsten absorbers, while an overall good agreement between data and simulations for all considered models is observed for steel.
• ### Performance of the first prototype of the CALICE scintillator strip electromagnetic calorimeter(1311.3761)

June 11, 2014 hep-ex, physics.ins-det
A first prototype of a scintillator strip-based electromagnetic calorimeter was built, consisting of 26 layers of tungsten absorber plates interleaved with planes of 45x10x3 mm3 plastic scintillator strips. Data were collected using a positron test beam at DESY with momenta between 1 and 6 GeV/c. The prototype's performance is presented in terms of the linearity and resolution of the energy measurement. These results represent an important milestone in the development of highly granular calorimeters using scintillator strip technology. This technology is being developed for a future linear collider experiment, aiming at the precise measurement of jet energies using particle flow techniques.
• ### Shower development of particles with momenta from 1 to 10 GeV in the CALICE Scintillator-Tungsten HCAL(1311.3505)

Jan. 13, 2014 physics.ins-det
Lepton colliders are considered as options to complement and to extend the physics programme at the Large Hadron Collider. The Compact Linear Collider (CLIC) is an $e^+e^-$ collider under development aiming at centre-of-mass energies of up to 3 TeV. For experiments at CLIC, a hadron sampling calorimeter with tungsten absorber is proposed. Such a calorimeter provides sufficient depth to contain high-energy showers, while allowing a compact size for the surrounding solenoid. A fine-grained calorimeter prototype with tungsten absorber plates and scintillator tiles read out by silicon photomultipliers was built and exposed to particle beams at CERN. Results obtained with electrons, pions and protons of momenta up to 10 GeV are presented in terms of energy resolution and shower shape studies. The results are compared with several GEANT4 simulation models in order to assess the reliability of the Monte Carlo predictions relevant for a future experiment at CLIC.
• ### Track segments in hadronic showers in a highly granular scintillator-steel hadron calorimeter(1305.7027)

July 29, 2013 hep-ex, physics.ins-det
We investigate the three dimensional substructure of hadronic showers in the CALICE scintillator-steel hadronic calorimeter. The high granularity of the detector is used to find track segments of minimum ionising particles within hadronic showers, providing sensitivity to the spatial structure and the details of secondary particle production in hadronic cascades. The multiplicity, length and angular distribution of identified track segments are compared to GEANT4 simulations with several different shower models. Track segments also provide the possibility for in-situ calibration of highly granular calorimeters.
• ### Hadronic energy resolution of a highly granular scintillator-steel hadron calorimeter using software compensation techniques(1207.4210)

Sept. 27, 2012 hep-ex, physics.ins-det
The energy resolution of a highly granular 1 m3 analogue scintillator-steel hadronic calorimeter is studied using charged pions with energies from 10 GeV to 80 GeV at the CERN SPS. The energy resolution for single hadrons is determined to be approximately 58%/sqrt(E/GeV}. This resolution is improved to approximately 45%/sqrt(E/GeV) with software compensation techniques. These techniques take advantage of the event-by-event information about the substructure of hadronic showers which is provided by the imaging capabilities of the calorimeter. The energy reconstruction is improved either with corrections based on the local energy density or by applying a single correction factor to the event energy sum derived from a global measure of the shower energy density. The application of the compensation algorithms to Geant4 simulations yield resolution improvements comparable to those observed for real data.
• ### Electromagnetic response of a highly granular hadronic calorimeter(1012.4343)

June 8, 2011 physics.ins-det
The CALICE collaboration is studying the design of high performance electromagnetic and hadronic calorimeters for future International Linear Collider detectors. For the hadronic calorimeter, one option is a highly granular sampling calorimeter with steel as absorber and scintillator layers as active material. High granularity is obtained by segmenting the scintillator into small tiles individually read out via silicon photo-multipliers (SiPM). A prototype has been built, consisting of thirty-eight sensitive layers, segmented into about eight thousand channels. In 2007 the prototype was exposed to positrons and hadrons using the CERN SPS beam, covering a wide range of beam energies and incidence angles. The challenge of cell equalization and calibration of such a large number of channels is best validated using electromagnetic processes. The response of the prototype steel-scintillator calorimeter, including linearity and uniformity, to electrons is investigated and described.
• ### CMS (LHC) Measurements and Unusual Cosmic Ray Events(1010.6017)

Nov. 12, 2010 hep-ex, astro-ph.HE
At the LHC, for the first time, laboratory energies are sufficiently large to reproduce the kind of reactions that occur when energetic cosmic rays strike the top of the atmosphere. The reaction products of interest for cosmic ray studies are produced at small angles, even with colliding beams. Most of the emphasis at the LHC is on rare processes that are studied with detectors at large angles. It is precision measurements at large angles that are expected to lead to discoveries of Higgs bosons and super symmetric particles. CMS currently has two small angle detectors, CASTOR and a Zero Degree Calorimeter (ZDC). CASTOR, at $0.7^{\circ}$ down to $0.08^{\circ}$, is designed to study "Centauro" and "long penetrating" events, observed in VHE cosmic-ray data. As a general purpose detector it also makes measurements of reaction products at forward angles from p-p collisions, which provide input for cosmic ray shower codes. The ZDC is small, 9 cm. wide, between the incoming and outgoing beam pipes out at a distance of 140 m. The ZDC measures neutral objects that follow the direction of the beam at the interaction point. If the long penetrating objects are spectators they could be seen in the ZDC if their charge to mass ratio, Z/A, is less than 0.2.
• ### Study of the interactions of pions in the CALICE silicon-tungsten calorimeter prototype(1004.4996)

April 28, 2010 hep-ex, physics.ins-det
A prototype silicon-tungsten electromagnetic calorimeter for an ILC detector was tested in 2007 at the CERN SPS test beam. Data were collected with electron and hadron beams in the energy range 8 to 80 GeV. The analysis described here focuses on the interactions of pions in the calorimeter. One of the main objectives of the CALICE program is to validate the Monte Carlo tools available for the design of a full-sized detector. The interactions of pions in the Si-W calorimeter are therefore confronted with the predictions of various physical models implemented in the GEANT4 simulation framework.
• ### Construction and Commissioning of the CALICE Analog Hadron Calorimeter Prototype(1003.2662)

March 13, 2010 hep-ex, physics.ins-det
An analog hadron calorimeter (AHCAL) prototype of 5.3 nuclear interaction lengths thickness has been constructed by members of the CALICE Collaboration. The AHCAL prototype consists of a 38-layer sandwich structure of steel plates and highly-segmented scintillator tiles that are read out by wavelength-shifting fibers coupled to SiPMs. The signal is amplified and shaped with a custom-designed ASIC. A calibration/monitoring system based on LED light was developed to monitor the SiPM gain and to measure the full SiPM response curve in order to correct for non-linearity. Ultimately, the physics goals are the study of hadron shower shapes and testing the concept of particle flow. The technical goal consists of measuring the performance and reliability of 7608 SiPMs. The AHCAL was commissioned in test beams at DESY and CERN. The entire prototype was completed in 2007 and recorded hadron showers, electron showers and muons at different energies and incident angles in test beams at CERN and Fermilab.
• ### Forward Physics with Rapidity Gaps at the LHC(0811.0120)

Aug. 3, 2009 hep-ph, hep-ex
A rapidity gap program with great potential can be realized at the Large Hadron Collider, LHC, by adding a few simple forward shower counters (FSCs) along the beam line on both sides of the main central detectors, such as CMS. Measurements of single diffractive cross sections down to the lowest masses can be made with an efficient level-1 trigger. Exceptionally, the detectors also make feasible the study of Central Diffractive Excitation, and in particular the reaction g + g to g + g, in the color singlet channel, effectively using the LHC as a gluon-gluon collider.
• ### Critical temperature for the nuclear liquid-gas phase transition (from multifragmentation and fission)(0801.4485)

Jan. 29, 2008 nucl-ex
Critical temperature Tc for the nuclear liquid-gas phase transition is stimated both from the multifragmentation and fission data. In the first case,the critical temperature is obtained by analysis of the IMF yields in p(8.1 GeV)+Au collisions within the statistical model of multifragmentation (SMM). In the second case, the experimental fission probability for excited 188Os is compared with the calculated one with Tc as a free parameter. It is concluded for both cases that the critical temperature is higher than 16 MeV.
• ### Measuring Photons and Neutrons at Zero Degrees in CMS(nucl-ex/0703001)

Feb. 28, 2007 nucl-ex
The CMS Zero Degree Calorimeters, ZDCs, will measure photons and neutrons emitted with |eta|> 8.6 from Pb+Pb, p+Pb and p+p collisions at sqrt(Snn)=5.5, 8.8 and 14 TeV respectively. The calorimeter consists of an electromagnetic part segmented in the horizontal direction and an hadronic part segmented into four units in depth. In addition CMS will have access to data from a segmented shower maximum detector being built for luminosity measurements. We will present detailed results from tests beam measurements taken at the CERN SPS. These data will be used to extrapolate the utility of the ZDCs to measure photons, and possibly pi0s in p+p and ultra-peripheral heavy-ion collisions. Data from the hadronic section can be used to estimate the number of participants in heavy ion-collisions. In addition we will discuss plans to use the detector to measure the reaction plane, thereby extending the sensitivity of the central detectors in CMS.
• ### Status of Zero Degree Calorimeter for CMS Experiment(nucl-ex/0608052)

Sept. 4, 2006 hep-ex, nucl-ex, physics.ins-det
The Zero Degree Calorimeter (ZDC) is integral part of the CMS experiment, especially, for heavy ion studies. The design of the ZDC includes two independent calorimeter sections: an electromagnetic section and a hadronic section. Sampling calorimeters using tungsten and quartz fibers have been chosen for the energy measurements. An overview of the ZDC is presented along with a current status of calorimeter's preparation for Day 1 of LHC.
• ### Time scale of the thermal multifragmentation in p(3.6 GeV) + Au collisions(nucl-ex/0603001)

March 14, 2006 nucl-ex
The relative angle correlation of intermediate mass fragments has been studied for p+Au collisions at 3.6 GeV. Strong suppression at small angles is observed caused by IMF-IMF Coulomb repulsion. Experimental correlation function is compared to that obtained by the multi-body Coulomb trajectory calculations with the various decay time of fragmenting system. The combined model including the empirically modified intranuclear cascade followed by statistical multifragmentation was used to generate starting conditions for these calculations. The model dependence of the results obtained has been carefully checked. The mean decay time of fragmenting system is found to be 85 +- 50 fm/c.
• ### Nuclear multifragmentation and fission: similarity and differences(nucl-ex/0602013)

Feb. 10, 2006 nucl-ex
Thermal multifragmentation of hot nuclei is interpreted as the nuclear liquid--fog phase transition deep inside the spinodal region. The experimental data for p(8.1GeV) + Au collisions are analyzed. It is concluded that the decay process of hot nuclei is characterized by two size parameters: transition state and freeze-out volumes. The similarity between dynamics of fragmentation and ordinary fission is discussed. The IMF emission time is related to the mean rupture time at the multi-scission point, which corresponds to the kinetic freeze-out configuration.
• ### Spinodal decomposition, nuclear fog and two characteristic volumes in thermal multifragmentation(nucl-ex/0410017)

Oct. 13, 2004 nucl-ex
Thermal multifragmentation of hot nuclei is interpreted as the nuclear liquid-fog phase transition inside the spinodal region. The experimental data for p(8.1GeV) + Au collisions are analyzed within the framework of the statistical multifragmentation model (SMM) for the events with emission of at least two IMFs. It is found that the partition of hot nuclei is specified after expansion to a volume equal to Vt = (2.6+-0.3) Vo, with Vo as the volume at normal density. However, the freeze-out volume is found to be twice as large: Vf = (5+-1) Vo.
• ### Two characteristic volumes in thermal nuclear multifragmentation(hep-ex/0406024)

June 8, 2004 hep-ex
The paper is devoted to the experimental determination of the space-time characteristics for the target multifragmentation in p(8.1GeV) + Au collisions. The experimental data on the fragment charge distribution and kinetic energy spectra are analyzed within the framework of the statistical multifragmentation model. It is found that the partition of hot nuclei is specified after expansion of the target spectator to a volume equal to Vt = (2.9 +- 0.2) Vo, with Vo as the volume at normal density. However, the freeze-out volume is found to be Vf = (11 +- 3) Vo. At freeze-out, all the fragments are well separated and only the Coulomb force should be taken into account. The results are in accordance with a scenario of spinodal disintegration of hot nuclei.
• ### Multifragmentation and nuclear phase transitions (liquid-fog and liquid-gas)(nucl-ex/0310009)

Oct. 10, 2003 nucl-ex
Thermal multifragmentation of hot nuclei is interpreted as the nuclear liquid-fog phase transition. The charge distributions of the intermediate mass fragments produced in p(3.6 GeV) + Au and p(8.1 GeV) + Au collisions are analyzed within the statistical multifragmentation model with the critical temperature for the nuclear liquid-gas phase transition Tc as a free parameter. The analysis presented here provides strong support for a value of Tc > 15 MeV.
• ### Critical Temperature for the Nuclear Liquid-Gas Phase Transition(nucl-ex/0302006)

Feb. 7, 2003 nucl-ex
The charge distribution of the intermediate mass fragments produced in p (8.1 GeV) + Au collisions is analyzed in the framework of the statistical multifragmentation model with the critical temperature for the nuclear liquid-gas phase transition $T_c$ as a free parameter. It is found that $T_c=20\pm3$ MeV (90% CL).