-
Fiber Bragg Grating (FBG) sensors have been so far mainly used in high energy
physics (HEP) as high precision positioning and re-positioning sensors and as
low cost, easy to mount, radiation hard and low space- consuming temperature
and humidity devices. FBGs are also commonly used for very precise strain
measurements. In this work we present a novel use of FBGs as flatness and
mechanical tensioning sensors applied to the wide Gas Electron Multiplier (GEM)
foils of the GE1/1 chambers of the Compact Muon Solenoid (CMS) experiment at
Large Hadron Collider (LHC) of CERN. A network of FBG sensors has been used to
determine the optimal mechanical tension applied and to characterize the
mechanical stress applied to the foils. The preliminary results of the test
performed on a full size GE1/1 final prototype and possible future developments
will be discussed.
-
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been
utilised to assess and monitor the flatness of Gaseous Electron Multipliers
(GEM) foils. The setup layout and preliminary results are presented.
-
We present a novel application of Fiber Bragg Grating (FBG) sensors in the
construction and characterisation of Micro Pattern Gaseous Detector (MPGD),
with particular attention to the realisation of the largest triple (Gas
electron Multiplier) GEM chambers so far operated, the GE1/1 chambers of the
CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of
about 0.5 m2 active area each, employing three GEM foils per chamber, to be
installed in the forward region of the CMS endcap during the long shutdown of
LHC in 2108-2019. The large active area of each GE1/1 chamber consists of GEM
foils that are mechanically stretched in order to secure their flatness and the
consequent uniform performance of the GE1/1 chamber across its whole active
surface. So far FBGs have been used in high energy physics mainly as high
precision positioning and re-positioning sensors and as low cost, easy to
mount, low space consuming temperature sensors. FBGs are also commonly used for
very precise strain measurements in material studies. In this work we present a
novel use of FBGs as flatness and mechanical tensioning sensors applied to the
wide GEM foils of the GE1/1 chambers. A network of FBG sensors have been used
to determine the optimal mechanical tension applied and to characterise the
mechanical tension that should be applied to the foils. We discuss the results
of the test done on a full-sized GE1/1 final prototype, the studies done to
fully characterise the GEM material, how this information was used to define a
standard assembly procedure and possible future developments.
-
Gas Electron Multiplier (GEM) technology is being considered for the forward
muon upgrade of the CMS experiment in Phase 2 of the CERN LHC. Its first
implementation is planned for the GE1/1 system in the $1.5 < \mid\eta\mid <
2.2$ region of the muon endcap mainly to control muon level-1 trigger rates
after the second long LHC shutdown. A GE1/1 triple-GEM detector is read out by
3,072 radial strips with 455 $\mu$rad pitch arranged in eight $\eta$-sectors.
We assembled a full-size GE1/1 prototype of 1m length at Florida Tech and
tested it in 20-120 GeV hadron beams at Fermilab using Ar/CO$_{2}$ 70:30 and
the RD51 scalable readout system. Four small GEM detectors with 2-D readout and
an average measured azimuthal resolution of 36 $\mu$rad provided precise
reference tracks. Construction of this largest GEM detector built to-date is
described. Strip cluster parameters, detection efficiency, and spatial
resolution are studied with position and high voltage scans. The plateau
detection efficiency is [97.1 $\pm$ 0.2 (stat)]\%. The azimuthal resolution is
found to be [123.5 $\pm$ 1.6 (stat)] $\mu$rad when operating in the center of
the efficiency plateau and using full pulse height information. The resolution
can be slightly improved by $\sim$ 10 $\mu$rad when correcting for the bias due
to discrete readout strips. The CMS upgrade design calls for readout
electronics with binary hit output. When strip clusters are formed
correspondingly without charge-weighting and with fixed hit thresholds, a
position resolution of [136.8 $\pm$ 2.5 stat] $\mu$rad is measured, consistent
with the expected resolution of strip-pitch/$\sqrt{12}$ = 131.3 $\mu$rad. Other
$\eta$-sectors of the detector show similar response and performance.
-
The CMS GEM collaboration is considering Gas Electron Multipliers (GEMs) for
upgrading the CMS forward muon system in the 1.5<|eta|<2.4 endcap region. GEM
detectors can provide precision tracking and fast trigger information. They
would improve the CMS muon trigger and muon momentum resolution and provide
missing redundancy in the high-eta region. Employing a new faster construction
and assembly technique, we built four full-scale Triple-GEM muon detectors for
the inner ring of the first muon endcap station. We plan to install these or
further improved versions in CMS during the first long LHC shutdown in 2013/14
for continued testing. These detectors are designed for the stringent rate and
resolution requirements in the increasingly hostile environments expected at
CMS after the second long LHC shutdown in 2018/19. The new prototypes were
studied in muon/pion beams at the CERN SPS. We discuss our experience with
constructing the new full-scale production prototypes and present preliminary
performance results from the beam test. We also tested smaller Triple-GEM
prototypes with zigzag readout strips with 2 mm pitch in these beams and
measured a spatial resolution of 73 microns. This readout offers a potential
reduction of channel count and consequently electronics cost for this system
while maintaining high spatial resolution.
-
At present, part of the forward RPC muon system of the CMS detector at the
CERN LHC remains uninstrumented in the high-\eta region. An international
collaboration is investigating the possibility of covering the 1.6 < |\eta| <
2.4 region of the muon endcaps with large-area triple-GEM detectors. Given
their good spatial resolution, high rate capability, and radiation hardness,
these micro-pattern gas detectors are an appealing option for simultaneously
enhancing muon tracking and triggering capabilities in a future upgrade of the
CMS detector. A general overview of this feasibility study will be presented.
The design and construction of small (10\times10 cm2) and full-size trapezoidal
(1\times0.5 m2) triple-GEM prototypes will be described. During detector
assembly, different techniques for stretching the GEM foils were tested.
Results from measurements with x-rays and from test beam campaigns at the CERN
SPS will be shown for the small and large prototypes. Preliminary simulation
studies on the expected muon reconstruction and trigger performances of this
proposed upgraded muon system will be reported.
-
Gas Electron Multipliers (GEM) are an interesting technology under
consideration for the future upgrade of the forward region of the CMS muon
system, specifically in the $1.6<| \eta |<2.4$ endcap region. With a
sufficiently fine segmentation GEMs can provide precision tracking as well as
fast trigger information. The main objective is to contribute to the
improvement of the CMS muon trigger. The construction of large-area GEM
detectors is challenging both from the technological and production aspects. In
view of the CMS upgrade we have designed and built the largest full-size
Triple-GEM muon detector, which is able to meet the stringent requirements
given the hostile environment at the high-luminosity LHC. Measurements were
performed during several test beam campaigns at the CERN SPS in 2010 and 2011.
The main issues under study are efficiency, spatial resolution and timing
performance with different inter-electrode gap configurations and gas mixtures.
In this paper results of the performance of the prototypes at the beam tests
will be discussed.
-
In view of a possible extension of the forward CMS muon detector system and
future LHC luminosity upgrades, Micro-Pattern Gas Detectors (MPGDs) are an
appealing technology. They can simultaneously provide precision tracking and
fast trigger information, as well as sufficiently fine segmentation to cope
with high particle rates in the high-eta region at LHC and its future upgrades.
We report on the design and construction of a full-size prototype for the CMS
endcap system, the largest Triple-GEM detector built to-date. We present
details on the 3D modeling of the detector geometry, the implementation of the
readout strips and electronics, and the detector assembly procedure.