-
The Compact Linear Collider (CLIC) is a multi-TeV high-luminosity linear e+e-
collider under development. For an optimal exploitation of its physics
potential, CLIC is foreseen to be built and operated in a staged approach with
three centre-of-mass energy stages ranging from a few hundred GeV up to 3 TeV.
The first stage will focus on precision Standard Model physics, in particular
Higgs and top-quark measurements. Subsequent stages will focus on measurements
of rare Higgs processes, as well as searches for new physics processes and
precision measurements of new states, e.g. states previously discovered at LHC
or at CLIC itself. In the 2012 CLIC Conceptual Design Report, a fully optimised
3 TeV collider was presented, while the proposed lower energy stages were not
studied to the same level of detail. This report presents an updated baseline
staging scenario for CLIC. The scenario is the result of a comprehensive study
addressing the performance, cost and power of the CLIC accelerator complex as a
function of centre-of-mass energy and it targets optimal physics output based
on the current physics landscape. The optimised staging scenario foresees three
main centre-of-mass energy stages at 380 GeV, 1.5 TeV and 3 TeV for a full CLIC
programme spanning 22 years. For the first stage, an alternative to the CLIC
drive beam scheme is presented in which the main linac power is produced using
X-band klystrons.
-
A large prototype of 1.3m3 was designed and built as a demonstrator of the
semi-digital hadronic calorimeter (SDHCAL) concept proposed for the future ILC
experiments. The prototype is a sampling hadronic calorimeter of 48 units. Each
unit is built of an active layer made of 1m2 Glass Resistive Plate
Chamber(GRPC) detector placed inside a cassette whose walls are made of
stainless steel. The cassette contains also the electronics used to read out
the GRPC detector. The lateral granularity of the active layer is provided by
the electronics pick-up pads of 1cm2 each. The cassettes are inserted into a
self-supporting mechanical structure built also of stainless steel plates
which, with the cassettes walls, play the role of the absorber. The prototype
was designed to be very compact and important efforts were made to minimize the
number of services cables to optimize the efficiency of the Particle Flow
Algorithm techniques to be used in the future ILC experiments. The different
components of the SDHCAL prototype were studied individually and strict
criteria were applied for the final selection of these components. Basic
calibration procedures were performed after the prototype assembling. The
prototype is the first of a series of new-generation detectors equipped with a
power-pulsing mode intended to reduce the power consumption of this highly
granular detector. A dedicated acquisition system was developed to deal with
the output of more than 440000 electronics channels in both trigger and
triggerless modes. After its completion in 2011, the prototype was commissioned
using cosmic rays and particles beams at CERN.
-
Application of Micromegas for sampling calorimetry puts specific constraints
on the design and performance of this gaseous detector. In particular, uniform
and linear response, low noise and stability against high ionisation density
deposits are prerequisites to achieving good energy resolution. A
Micromegas-based hadronic calorimeter was proposed for an application at a
future linear collider experiment and three technologically advanced prototypes
of 1$\times$1 m$^{2}$ were constructed. Their merits relative to the
above-mentioned criteria are discussed on the basis of measurements performed
at the CERN SPS test-beam facility.
-
Lepton colliders are considered as options to complement and to extend the
physics programme at the Large Hadron Collider. The Compact Linear Collider
(CLIC) is an $e^+e^-$ collider under development aiming at centre-of-mass
energies of up to 3 TeV. For experiments at CLIC, a hadron sampling calorimeter
with tungsten absorber is proposed. Such a calorimeter provides sufficient
depth to contain high-energy showers, while allowing a compact size for the
surrounding solenoid.
A fine-grained calorimeter prototype with tungsten absorber plates and
scintillator tiles read out by silicon photomultipliers was built and exposed
to particle beams at CERN. Results obtained with electrons, pions and protons
of momenta up to 10 GeV are presented in terms of energy resolution and shower
shape studies. The results are compared with several GEANT4 simulation models
in order to assess the reliability of the Monte Carlo predictions relevant for
a future experiment at CLIC.
-
We investigate the three dimensional substructure of hadronic showers in the
CALICE scintillator-steel hadronic calorimeter. The high granularity of the
detector is used to find track segments of minimum ionising particles within
hadronic showers, providing sensitivity to the spatial structure and the
details of secondary particle production in hadronic cascades. The
multiplicity, length and angular distribution of identified track segments are
compared to GEANT4 simulations with several different shower models. Track
segments also provide the possibility for in-situ calibration of highly
granular calorimeters.
-
During 2011 the LHCb experiment at CERN collected 1.0 fb-1 of sqrt{s} = 7 TeV
pp collisions. Due to the large heavy quark production cross-sections, these
data provide unprecedented samples of heavy flavoured hadrons. The first
results from LHCb have made a significant impact on the flavour physics
landscape and have definitively proved the concept of a dedicated experiment in
the forward region at a hadron collider. This document discusses the
implications of these first measurements on classes of extensions to the
Standard Model, bearing in mind the interplay with the results of searches for
on-shell production of new particles at ATLAS and CMS. The physics potential of
an upgrade to the LHCb detector, which would allow an order of magnitude more
data to be collected, is emphasised.
-
The energy resolution of a highly granular 1 m3 analogue scintillator-steel
hadronic calorimeter is studied using charged pions with energies from 10 GeV
to 80 GeV at the CERN SPS. The energy resolution for single hadrons is
determined to be approximately 58%/sqrt(E/GeV}. This resolution is improved to
approximately 45%/sqrt(E/GeV) with software compensation techniques. These
techniques take advantage of the event-by-event information about the
substructure of hadronic showers which is provided by the imaging capabilities
of the calorimeter. The energy reconstruction is improved either with
corrections based on the local energy density or by applying a single
correction factor to the event energy sum derived from a global measure of the
shower energy density. The application of the compensation algorithms to Geant4
simulations yield resolution improvements comparable to those observed for real
data.
-
Calorimetry at future linear colliders could be based on a particle flow
approach where granularity is the key to high jet energy resolution. Among
different technologies, Micromegas chambers with 1 cm2 pad segmentation are
studied for the active medium of a hadronic calorimeter. A chamber of 1 m2 with
9216 channels read out by a low noise front-end ASIC called MICROROC has
recently been constructed and tested. Chamber design, ASIC circuitry and
preliminary test beam results are reported.
-
The CALICE collaboration is studying the design of high performance
electromagnetic and hadronic calorimeters for future International Linear
Collider detectors. For the hadronic calorimeter, one option is a highly
granular sampling calorimeter with steel as absorber and scintillator layers as
active material. High granularity is obtained by segmenting the scintillator
into small tiles individually read out via silicon photo-multipliers (SiPM).
A prototype has been built, consisting of thirty-eight sensitive layers,
segmented into about eight thousand channels. In 2007 the prototype was exposed
to positrons and hadrons using the CERN SPS beam, covering a wide range of beam
energies and incidence angles. The challenge of cell equalization and
calibration of such a large number of channels is best validated using
electromagnetic processes.
The response of the prototype steel-scintillator calorimeter, including
linearity and uniformity, to electrons is investigated and described.
-
The recent progress in R&D of the Micromegas detectors for hadronic
calorimetry including new engineering-technical solutions, electronics
development, and accompanying simulation studies with emphasis on the
comparison of the physics performance of the analog and digital readout is
described. The developed prototypes are with 2 bit digital readout to exploit
the Micromegas proportional mode and thus improve the calorimeter linearity. In
addition, measurements of detection efficiency, hit multiplicity, and energy
shower profiles obtained during the exposure of small size prototypes to
radioactive source quanta, cosmic particles and accelerator beams are reported.
Eventually, the status of a large scale chamber (1{\times}1 m2) are also
presented with prospective towards the construction of a 1 m3 digital
calorimeter consisting of 40 such chambers.
-
The activities towards the fabrication and test of a 1 m3 semi-digital
hadronic calorime- ter are reviewed. The prototype sampling planes would
consist of 1 m2 Micromegas chambers with 1 cm2 granularity and embedded 2 bits
readout suitable for PFA calorime- try at an ILC detector. The design of the 1
m2 chamber is presented first, followed by an overview of the basic performance
of small prototypes. The basic units composing the 1 m2 chamber are 32 \times
48 cm2 boards with integrated electronics and a micro-mesh. Results of
character- ization tests of such boards are shown. Micromegas as a proportional
detector is well suited for semi-digital hadronic calorimetry. In order to
quantify the gain in perfor- mance when using one or more thresholds,
simulation studies are being carried out, some of which will be reported in
this contribution.
-
Prototypes of MICROMEGAS chambers, using bulk technology and analog readout,
with 1x1cm2 readout segmentation have been built and tested. Measurements in
Ar/iC4H10 (95/5) and Ar/CO2 (80/20) are reported. The dependency of the
prototypes gas gain versus pressure, gas temperature and amplification gap
thickness variations has been measured with an 55Fe source and a method for
temperature and pressure correction of data is presented. A stack of four
chambers has been tested in 200GeV/c and 7GeV/c muon and pion beams
respectively. Measurements of response uniformity, detection efficiency and hit
multiplicity are reported. A bulk MICROMEGAS prototype with embedded digital
readout electronics has been assembled and tested. The chamber layout and first
results are presented.
The Compact Linear Collider (CLIC) is a multi-TeV high-luminosity linear e+e- collider under development. For an optimal exploitation of its physics potential, CLIC is foreseen to be built and operated in a staged approach with three centre-of-mass energy stages ranging from a few hundred GeV up to 3 TeV. The first stage will focus on precision Standard Model physics, in particular Higgs and top-quark measurements. Subsequent stages will focus on measurements of rare Higgs processes, as well as searches for new physics processes and precision measurements of new states, e.g. states previously discovered at LHC or at CLIC itself. In the 2012 CLIC Conceptual Design Report, a fully optimised 3 TeV collider was presented, while the proposed lower energy stages were not studied to the same level of detail. This report presents an updated baseline staging scenario for CLIC. The scenario is the result of a comprehensive study addressing the performance, cost and power of the CLIC accelerator complex as a function of centre-of-mass energy and it targets optimal physics output based on the current physics landscape. The optimised staging scenario foresees three main centre-of-mass energy stages at 380 GeV, 1.5 TeV and 3 TeV for a full CLIC programme spanning 22 years. For the first stage, an alternative to the CLIC drive beam scheme is presented in which the main linac power is produced using X-band klystrons.
A large prototype of 1.3m3 was designed and built as a demonstrator of the semi-digital hadronic calorimeter (SDHCAL) concept proposed for the future ILC experiments. The prototype is a sampling hadronic calorimeter of 48 units. Each unit is built of an active layer made of 1m2 Glass Resistive Plate Chamber(GRPC) detector placed inside a cassette whose walls are made of stainless steel. The cassette contains also the electronics used to read out the GRPC detector. The lateral granularity of the active layer is provided by the electronics pick-up pads of 1cm2 each. The cassettes are inserted into a self-supporting mechanical structure built also of stainless steel plates which, with the cassettes walls, play the role of the absorber. The prototype was designed to be very compact and important efforts were made to minimize the number of services cables to optimize the efficiency of the Particle Flow Algorithm techniques to be used in the future ILC experiments. The different components of the SDHCAL prototype were studied individually and strict criteria were applied for the final selection of these components. Basic calibration procedures were performed after the prototype assembling. The prototype is the first of a series of new-generation detectors equipped with a power-pulsing mode intended to reduce the power consumption of this highly granular detector. A dedicated acquisition system was developed to deal with the output of more than 440000 electronics channels in both trigger and triggerless modes. After its completion in 2011, the prototype was commissioned using cosmic rays and particles beams at CERN.
Application of Micromegas for sampling calorimetry puts specific constraints on the design and performance of this gaseous detector. In particular, uniform and linear response, low noise and stability against high ionisation density deposits are prerequisites to achieving good energy resolution. A Micromegas-based hadronic calorimeter was proposed for an application at a future linear collider experiment and three technologically advanced prototypes of 1$\times$1 m$^{2}$ were constructed. Their merits relative to the above-mentioned criteria are discussed on the basis of measurements performed at the CERN SPS test-beam facility.
We investigate the three dimensional substructure of hadronic showers in the CALICE scintillator-steel hadronic calorimeter. The high granularity of the detector is used to find track segments of minimum ionising particles within hadronic showers, providing sensitivity to the spatial structure and the details of secondary particle production in hadronic cascades. The multiplicity, length and angular distribution of identified track segments are compared to GEANT4 simulations with several different shower models. Track segments also provide the possibility for in-situ calibration of highly granular calorimeters.
The energy resolution of a highly granular 1 m3 analogue scintillator-steel hadronic calorimeter is studied using charged pions with energies from 10 GeV to 80 GeV at the CERN SPS. The energy resolution for single hadrons is determined to be approximately 58%/sqrt(E/GeV}. This resolution is improved to approximately 45%/sqrt(E/GeV) with software compensation techniques. These techniques take advantage of the event-by-event information about the substructure of hadronic showers which is provided by the imaging capabilities of the calorimeter. The energy reconstruction is improved either with corrections based on the local energy density or by applying a single correction factor to the event energy sum derived from a global measure of the shower energy density. The application of the compensation algorithms to Geant4 simulations yield resolution improvements comparable to those observed for real data.
Calorimetry at future linear colliders could be based on a particle flow approach where granularity is the key to high jet energy resolution. Among different technologies, Micromegas chambers with 1 cm2 pad segmentation are studied for the active medium of a hadronic calorimeter. A chamber of 1 m2 with 9216 channels read out by a low noise front-end ASIC called MICROROC has recently been constructed and tested. Chamber design, ASIC circuitry and preliminary test beam results are reported.
The CALICE collaboration is studying the design of high performance electromagnetic and hadronic calorimeters for future International Linear Collider detectors. For the hadronic calorimeter, one option is a highly granular sampling calorimeter with steel as absorber and scintillator layers as active material. High granularity is obtained by segmenting the scintillator into small tiles individually read out via silicon photo-multipliers (SiPM). A prototype has been built, consisting of thirty-eight sensitive layers, segmented into about eight thousand channels. In 2007 the prototype was exposed to positrons and hadrons using the CERN SPS beam, covering a wide range of beam energies and incidence angles. The challenge of cell equalization and calibration of such a large number of channels is best validated using electromagnetic processes. The response of the prototype steel-scintillator calorimeter, including linearity and uniformity, to electrons is investigated and described.
The recent progress in R&D of the Micromegas detectors for hadronic calorimetry including new engineering-technical solutions, electronics development, and accompanying simulation studies with emphasis on the comparison of the physics performance of the analog and digital readout is described. The developed prototypes are with 2 bit digital readout to exploit the Micromegas proportional mode and thus improve the calorimeter linearity. In addition, measurements of detection efficiency, hit multiplicity, and energy shower profiles obtained during the exposure of small size prototypes to radioactive source quanta, cosmic particles and accelerator beams are reported. Eventually, the status of a large scale chamber (1{\times}1 m2) are also presented with prospective towards the construction of a 1 m3 digital calorimeter consisting of 40 such chambers.
The activities towards the fabrication and test of a 1 m3 semi-digital hadronic calorime- ter are reviewed. The prototype sampling planes would consist of 1 m2 Micromegas chambers with 1 cm2 granularity and embedded 2 bits readout suitable for PFA calorime- try at an ILC detector. The design of the 1 m2 chamber is presented first, followed by an overview of the basic performance of small prototypes. The basic units composing the 1 m2 chamber are 32 \times 48 cm2 boards with integrated electronics and a micro-mesh. Results of character- ization tests of such boards are shown. Micromegas as a proportional detector is well suited for semi-digital hadronic calorimetry. In order to quantify the gain in perfor- mance when using one or more thresholds, simulation studies are being carried out, some of which will be reported in this contribution.