• This paper studies the performance of cache-enabled dense small cell networks consisting of multi-antenna sub-6 GHz and millimeter-wave base stations. Different from the existing works which only consider a single antenna at each base station, the optimal content placement is unknown when the base stations have multiple antennas. We first derive the successful content delivery probability by accounting for the key channel features at sub-6 GHz and mmWave frequencies. The maximization of the successful content delivery probability is a challenging problem. To tackle it, we first propose a constrained cross-entropy algorithm which achieves the near-optimal solution with moderate complexity. We then develop another simple yet effective heuristic probabilistic content placement scheme, termed two-stair algorithm, which strikes a balance between caching the most popular contents and achieving content diversity. Numerical results demonstrate the superior performance of the constrained cross-entropy method and that the two-stair algorithm yields significantly better performance than only caching the most popular contents. The comparisons between the sub-6 GHz and mmWave systems reveal an interesting tradeoff between caching capacity and density for the mmWave system to achieve similar performance as the sub-6 GHz system.
  • This letter studies bi-directional secure information exchange in a simultaneous wireless information and power transfer (SWIPT) system enabled by a full-duplex (FD) multiple-input multiple-output (MIMO) amplify-and-forward (AF) relay. The AF relay injects artificial noise (AN) in order to confuse the eavesdropper. Specifically, we assume a zeroforcing (ZF) solution constraint to eliminate the residual self-interference (RSI). As a consequence, we address the optimal joint design of the ZF matrix and the AN covariance matrix at the relay node as well as the transmit power at the sources. We propose an alternating algorithm utilizing semi-definite programming (SDP) technique and one-dimensional searching to achieve the optimal solution. Simulation results are provided to demonstrate the effectiveness of the proposed algorithm.
  • Heterogeneous ultra-dense networks enable ultra-high data rates and ultra-low latency through the use of dense sub-6 GHz and millimeter wave (mmWave) small cells with different antenna configurations. Existing work has widely studied spectral and energy efficiency in such networks and shown that high spectral and energy efficiency can be achieved. This article investigates the benefits of heterogeneous ultra-dense network architecture from the perspectives of three promising technologies, i.e., physical layer security, caching, and wireless energy harvesting, and provides enthusiastic outlook towards application of these technologies in heterogeneous ultra-dense networks. Based on the rationale of each technology, opportunities and challenges are identified to advance the research in this emerging network.
  • We propose techniques for optimizing transmit beamforming in a full-duplex multiple-input-multiple-output (MIMO) wireless-powered communication system, which consists of two phases. In the first phase, the wireless-powered mobile station (MS) harvests energy using signals from the base station (BS), whereas in the second phase, both MS and BS communicate to each other in a full-duplex mode. When complete instantaneous channel state information (CSI) is available, the BS beamformer and the time-splitting (TS) parameter of energy harvesting are jointly optimized in order to obtain the BS-MS rate region. The joint optimization problem is non-convex, however, a computationally efficient optimum technique, based upon semidefinite relaxation and line-search, is proposed to solve the problem. A sub-optimum zero-forcing approach is also proposed, in which a closed-form solution of TS parameter is obtained. When only second-order statistics of transmit CSI is available, we propose to maximize the ergodic information rate at the MS, while maintaining the outage probability at the BS below a certain threshold. An upper bound for the outage probability is also derived and an approximate convex optimization framework is proposed for efficiently solving the underlying non-convex problem. Simulations demonstrate the advantages of the proposed methods over the sub-optimum and half-duplex ones.
  • This paper brings the novel idea of paying the utility to the winning agents in terms of some physical entity in cooperative communications. Our setting is a secret two-way communication channel where two transmitters exchange information in the presence of an eavesdropper. The relays are selected from a set of interested parties such that the secrecy sum rate is maximized. In return, the selected relay nodes' energy harvesting requirements will be fulfilled up to a certain threshold through their own payoff so that they have the natural incentive to be selected and involved in the communication. However, relays may exaggerate their private information in order to improve their chance to be selected. Our objective is to develop a mechanism for relay selection that enforces them to reveal the truth since otherwise they may be penalized. We also propose a joint cooperative relay beamforming and transmit power optimization scheme based on an alternating optimization approach. Note that the problem is highly non-convex since the objective function appears as a product of three correlated Rayleigh quotients. While a common practice in the existing literature is to optimize the relay beamforming vector for given transmit power via rank relaxation, we propose a second-order cone programming (SOCP)-based approach in this paper which requires a significantly lower computational task. The performance of the incentive control mechanism and the optimization algorithm has been evaluated through numerical simulations.
  • This paper investigates a multiuser multiple-input single-output (MISO) full-duplex (FD) system for simultaneous wireless information and power transfer (SWIPT), in which a multi-antenna base station (BS) simultaneously sends wirelessly information and power to a set of single-antenna mobile stations (MSs) using power splitters (PSs) in the downlink and receives information in the uplink in FD mode. In particular, we address the joint design of the receive PS ratio and the transmit power at the MSs, and the beamforming matrix at the BS under signal-to-interference-plus-noise ratio (SINR) and the harvested power constraints. Using semidefinite relaxation (SDR), we obtain the solution to the problem with imperfect channel state information (CSI) of the self-interfering channels. Furthermore, we propose another suboptimal zero-forcing (ZF) based solution by separating the optimization of the transmit beamforming vector and the PS ratio. Simulation results are provided to evaluate the performance of the proposed beamforming designs.
  • In this paper, we consider a three-node cooperative wireless powered communication system consisting of a multi-antenna hybrid access point (H-AP) and a single-antenna relay and a single-antenna user. The energy constrained relay and user first harvest energy in the downlink and then the relay assists the user using the harvested power for information transmission in the uplink. The optimal energy beamforming vector and the time split between harvest and cooperation are investigated. To reduce the computational complexity, suboptimal designs are also studied, where closed-form expressions are derived for the energy beamforming vector and the time split. For comparison purposes, we also present a detailed performance analysis in terms of the achievable outage probability and the average throughput of an intuitive energy beamforming scheme, where the H-AP directs all the energy towards the user. The findings of the paper suggest that implementing multiple antennas at the H-AP can significantly improve the system performance, and the closed-form suboptimal energy beamforming vector and time split yields near optimal performance. Also, for the intuitive beamforming scheme, a diversity order of (N+1)/2 can be achieved, where N is the number of antennas at the H-AP.
  • In this paper, we provide a theoretical framework for the study of massive multiple-input multiple-output (MIMO)-enabled full-duplex (FD) cellular networks in which the self-interference (SI) channels follow the Rician distribution and other channels are Rayleigh distributed. To facilitate bi-directional wireless functionality, we adopt (i) a downlink (DL) linear zero-forcing with self-interference-nulling (ZF-SIN) precoding scheme at the FD base stations (BSs), and (ii) an uplink (UL) self-interference-aware (SIA) fractional power control mechanism at the FD user equipments (UEs). Linear ZF receivers are further utilized for signal detection in the UL. The results indicate that the UL rate bottleneck in the baseline FD single-antenna system can be overcome via exploiting massive MIMO. On the other hand, the findings may be viewed as a reality-check, since we show that, under state-of-the-art system parameters, the spectral efficiency (SE) gain of FD massive MIMO over its half-duplex (HD) counterpart largely depends on the SI cancellation capability of the UEs. In addition, the anticipated two-fold increase in SE is shown to be only achievable with an infinitely large number of antennas.
  • Physical layer security has been recently recognized as a promising new design paradigm to provide security in wireless networks. In addition to the existing conventional cryptographic methods, physical layer security exploits the dynamics of fading channels to enhance secured wireless links. In this approach, jamming plays a key role by generating noise signals to confuse the potential eavesdroppers, and significantly improves quality and reliability of secure communications between legitimate terminals. This article presents theoretical limits and practical designs of jamming approaches for physical layer security. In particular, the theoretical limits explore the achievable secrecy rates of user cooperation based jamming whilst the centralized, and game theoretic based precoding techniques are reviewed for practical implementations. In addition, the emerging wireless energy harvesting techniques are exploited to harvest the required energy to transmit jamming signals. Future directions of these approaches, and the associated research challenges are also briefly outlined.
  • We consider a multi-user multiple-input multiple-output (MIMO) setup where full-duplex (FD) multi-antenna nodes apply linear beamformers to simultaneously transmit and receive multiple streams over Rician fading channels. The exact first and second positive moments of the residual self-interference (SI), involving the squared norm of a sum of non-identically distributed random variables, are derived in closed-form. The method of moments is hence invoked to provide a Gamma approximation for the residual SI distribution. The proposed theorem holds under arbitrary linear precoder/decoder design, number of antennas and streams, and SI cancellation capability.
  • Network coding is an efficient means to improve the spectrum efficiency of satellite communications. However, its resilience to eavesdropping attacks is not well understood. This paper studies the confidentiality issue in a bidirectional satellite network consisting of two mobile users who want to exchange message via a multibeam satellite using the XOR network coding protocol. We aim to maximize the sum secrecy rate by designing the optimal beamforming vector along with optimizing the return and forward link time allocation. The problem is non-convex, and we find its optimal solution using semidefinite programming together with a 1-D search. For comparison, we also solve the sum secrecy rate maximization problem for a conventional reference scheme without using network coding. Simulation results using realistic system parameters demonstrate that the bidirectional scheme using network coding provides considerably higher secrecy rate compared to that of the conventional scheme.
  • Interference in wireless networks degrades the signal quality at the terminals. However, it can potentially enhance the secrecy rate. This paper investigates the secrecy rate in a two-user interference network where one of the users, namely user 1, requires to establish a confidential connection. User 1 wants to prevent an unintended user of the network to decode its transmission. User 1 has to transmit such that its secrecy rate is maximized while the quality of service at the destination of the other user, user 2, is satisfied, and both user's power limits are taken into account. We consider two scenarios: 1) user 2 changes its power in favor of user 1, an altruistic scenario, 2) user 2 is selfish and only aims to maintain the minimum quality of service at its destination, an egoistic scenario. It is shown that there is a threshold for user 2's transmission power that only below or above which, depending on the channel qualities, user 1 can achieve a positive secrecy rate. Closed-form solutions are obtained in order to perform joint optimal power control. Further, a new metric called secrecy energy efficiency is introduced. We show that in general, the secrecy energy efficiency of user 1 in an interference channel scenario is higher than that of an interference-free channel.
  • We consider a full-duplex (FD) decode-and-forward system in which the time-switching protocol is employed by the multi-antenna relay to receive energy from the source and transmit information to the destination. The instantaneous throughput is maximized by optimizing receive and transmit beamformers at the relay and the time-split parameter. We study both optimum and suboptimum schemes. The reformulated problem in the optimum scheme achieves closed-form solutions in terms of transmit beamformer for some scenarios. In other scenarios, the optimization problem is formulated as a semi-definite relaxation problem and a rank-one optimum solution is always guaranteed. In the suboptimum schemes, the beamformers are obtained using maximum ratio combining, zero-forcing, and maximum ratio transmission. When beamformers have closed-form solutions, the achievable instantaneous and delay-constrained throughput are analytically characterized. Our results reveal that, beamforming increases both the energy harvesting and loop interference suppression capabilities at the FD relay. Moreover, simulation results demonstrate that the choice of the linear processing scheme as well as the time-split plays a critical role in determining the FD gains.
  • We consider a full-duplex decode-and-forward system, where the wirelessly powered relay employs the time-switching protocol to receive power from the source and then transmit information to the destination. It is assumed that the relay node is equipped with two sets of antennas to enable full-duplex communications. Three different interference mitigation schemes are studied, namely, 1) optimal 2) zero-forcing and 3) maximum ratio combining/maximum ratio transmission. We develop new outage probability expressions to investigate delay-constrained transmission throughput of these schemes. Our analysis show interesting performance comparisons of the considered precoding schemes for different system and link parameters.
  • This paper maximizes the achievable throughput of a relay-assisted wirelessly powered communications system, where an energy constrained source, helped by an energy constrained relay and both powered by a dedicated power beacon (PB), communicates with a destination. Considering the time splitting approach, the source and relay first harvest energy from the PB, which is equipped with multiple antennas, and then transmits information to the destination. Simple closed-form expressions are derived for the optimal PB energy beamforming vector and time split for energy harvesting and information transmission. Numerical results and simulations demonstrate the superior performance compared with some intuitive benchmark beamforming scheme. Also, it is found that placing the relay at the middle of the source-destination path is no longer optimal.
  • This article discusses opportunities and challenges of physical layer security integration in massive multiple-input multiple-output (MaMIMO) systems. Specifically, we first show that MaMIMO itself is robust against passive eavesdropping attacks. We then review a pilot contamination scheme which actively attacks the channel estimation process. This pilot contamination attack is not only dramatically reducing the achievable secrecy capacity but is also difficult to detect. We proceed by reviewing some methods from literature that detect active attacks on MaMIMO. The last part of the paper surveys the open research problems that we believe are the most important to address in the future and give a few promising directions of research to solve them.
  • In this paper we propose a power-efficient transfer of information and energy, where we exploit the constructive part of wireless interference as a source of green useful signal power. Rather than suppressing interference as in conventional schemes, we take advantage of constructive interference among users, inherent in the downlink, as a source of both useful information and wireless energy. Specifically, we propose a new precoding design that minimizes the transmit power while guaranteeing the quality of service (QoS) and energy harvesting constraints for generic phase shift keying modulated signals. The QoS constraints are modified to accommodate constructive interference. We derive a sub-optimal solution and a local optimum solution to the precoding optimization problem. The proposed precoding reduces the transmit power compared to conventional schemes, by adapting the constraints to accommodate constructive interference as a source of useful signal power. Our simulation results show significant power savings with the proposed data-aided precoding compared to the conventional precoding.
  • In this paper we explore the use of full-duplex radio to improve the spectrum efficiency in a two-way relay channel where two sources exchange information through an multi-antenna relay, and all nodes work in the full-duplex mode. The full-duplex operation can reduce the overall communication to only one phase but suffers from the self-interference. Instead of purely suppressing the self-interference, we aim to maximize the end-to-end performance by jointly optimizing the beamforming matrix at the relay which uses the amplify-and-forward protocol as well as the power control at the sources. To be specific, we propose iterative algorithms and 1-D search to solve two problems: finding the achievable rate region and maximizing the sum rate. At each iteration, either the analytical solution or convex formulation is obtained. We compare the proposed full-duplex two-way relaying with the conventional half-duplex two-way relaying, a full-duplex one-way relaying and a performance upper bound. Numerical results show that the proposed full-duplex scheme significantly improves the achievable data rates over the conventional scheme.
  • We consider a dual-hop full-duplex relaying system, where the energy constrained relay node is powered by radio frequency signals from the source using the time-switching architecture, both the amplify-and-forward and decode-and-forward relaying protocols are studied. Specifically, we provide an analytical characterization of the achievable throughput of three different communication modes, namely, instantaneous transmission, delay-constrained transmission, and delay tolerant transmission. In addition, the optimal time split is studied for different transmission modes. Our results reveal that, when the time split is optimized, the full-duplex relaying could substantially boost the system throughput compared to the conventional half-duplex relaying architecture for all three transmission modes. In addition, it is shown that the instantaneous transmission mode attains the highest throughput. However, compared to the delay-constrained transmission mode, the throughput gap is rather small. Unlike the instantaneous time split optimization which requires instantaneous channel state information, the optimal time split in the delay-constrained transmission mode depends only on the statistics of the channel, hence, is suitable for practical implementations.
  • Energy harvesting for wireless communication networks is a new paradigm that allows terminals to recharge their batteries from external energy sources in the surrounding environment. A promising energy harvesting technology is wireless power transfer where terminals harvest energy from electromagnetic radiation. Thereby, the energy may be harvested opportunistically from ambient electromagnetic sources or from sources that intentionally transmit electromagnetic energy for energy harvesting purposes. A particularly interesting and challenging scenario arises when sources perform simultaneous wireless information and power transfer (SWIPT), as strong signals not only increase power transfer but also interference. This paper provides an overview of SWIPT systems with a particular focus on the hardware realization of rectenna circuits and practical techniques that achieve SWIPT in the domains of time, power, antennas, and space. The paper also discusses the benefits of a potential integration of SWIPT technologies in modern communication networks in the context of resource allocation and cooperative cognitive radio networks.
  • This article re-examines the fundamental notion of interference in wireless networks by contrasting traditional approaches to new concepts that handle interference in a creative way. Specifically, we discuss the fundamental limits of the interference channel and present the interference alignment technique and its extension of signal alignment techniques. Contrary to this traditional view, which treats interference as a detrimental phenomenon, we introduce three concepts that handle interference as a useful resource. The first concept exploits interference at the modulation level and leads to simple multiuser downlink precoding that provides significant energy savings. The second concept uses radio frequency radiation for energy harvesting and handles interference as a source of green energy. The last concept refers to a secrecy environment and uses interference as an efficient means to jam potential eavesdroppers. These three techniques bring a new vision about interference in wireless networks and motivate a plethora of potential new applications and services.
  • Cooperation between the primary and secondary systems can improve the spectrum efficiency in cognitive radio networks. The key idea is that the secondary system helps to boost the primary system's performance by relaying and in return the primary system provides more opportunities for the secondary system to access the spectrum. In contrast to most of existing works that only consider information cooperation, this paper studies joint information and energy cooperation between the two systems, i.e., the primary transmitter sends information for relaying and feeds the secondary system with energy as well. This is particularly useful when the secondary transmitter has good channel quality to the primary receiver but is energy constrained. We propose and study three schemes that enable this cooperation. Firstly, we assume there exists an ideal backhaul between the two systems for information and energy transfer. We then consider two wireless information and energy transfer schemes from the primary transmitter to the secondary transmitter using power splitting and time splitting energy harvesting techniques, respectively. For each scheme, the optimal and zero-forcing solutions are derived. Simulation results demonstrate promising performance gain for both systems due to the additional energy cooperation. It is also revealed that the power splitting scheme can achieve larger rate region than the time splitting scheme when the efficiency of the energy transfer is sufficiently large.
  • We consider a multiuser multiple-input single-output interference channel where the receivers are characterized by both quality-of-service (QoS) and radio-frequency (RF) energy harvesting (EH) constraints. We consider the power splitting RF-EH technique where each receiver divides the received signal into two parts a) for information decoding and b) for battery charging. The minimum required power that supports both the QoS and the RF-EH constraints is formulated as an optimization problem that incorporates the transmitted power and the beamforming design at each transmitter as well as the power splitting ratio at each receiver. We consider both the cases of fixed beamforming and when the beamforming design is incorporated into the optimization problem. For fixed beamforming we study three standard beamforming schemes, the zero-forcing (ZF), the regularized zero-forcing (RZF) and the maximum ratio transmission (MRT); a hybrid scheme, MRT-ZF, comprised of a linear combination of MRT and ZF beamforming is also examined. The optimal solution for ZF beamforming is derived in closed-form, while optimization algorithms based on second-order cone programming are developed for MRT, RZF and MRT-ZF beamforming to solve the problem. In addition, the joint-optimization of beamforming and power allocation is studied using semidefinite programming (SDP) with the aid of rank relaxation.
  • In this paper, we deal with the deployment of full-duplex relaying in amplify-and-forward (AF) cooperative networks with multiple-antenna terminals. In contrast to previous studies, which focus on the spatial mitigation of the loopback interference (LI) at the relay node, a joint precoding/decoding design that maximizes the end-to-end (e2e) performance is investigated. The proposed precoding incorporates rank-1 zero-forcing (ZF) LI suppression at the relay node and is derived in closed-form by solving appropriate optimization problems. In order to further reduce system complexity, the antenna selection (AS) problem for full-duplex AF cooperative systems is discussed. We investigate different AS schemes to select a single transmit antenna at both the source and the relay, as well as a single receive antenna at both the relay and the destination. To facilitate comparison, exact outage probability expressions and asymptotic approximations of the proposed AS schemes are provided. In order to overcome zero-diversity effects associated with the AS operation, a simple power allocation scheme at the relay node is also investigated and its optimal value is analytically derived. Numerical and simulation results show that the joint ZF-based precoding significantly improves e2e performance, while AS schemes are efficient solutions for scenarios with strict computational constraints.
  • This paper studies secrecy rate optimization in a wireless network with a single-antenna source, a multi-antenna destination and a multi-antenna eavesdropper. This is an unfavorable scenario for secrecy performance as the system is interference-limited. In the literature, assuming that the receiver operates in half duplex (HD) mode, the aforementioned problem has been addressed via use of cooperating nodes who act as jammers to confound the eavesdropper. This paper investigates an alternative solution, which assumes the availability of a full duplex (FD) receiver. In particular, while receiving data, the receiver transmits jamming noise to degrade the eavesdropper channel. The proposed self-protection scheme eliminates the need for external helpers and provides system robustness. For the case in which global channel state information is available, we aim to design the optimal jamming covariance matrix that maximizes the secrecy rate and mitigates loop interference associated with the FD operation. We consider both fixed and optimal linear receiver design at the destination, and show that the optimal jamming covariance matrix is rank-1, and can be found via an efficient 1-D search. For the case in which only statistical information on the eavesdropper channel is available, the optimal power allocation is studied in terms of ergodic and outage secrecy rates. Simulation results verify the analysis and demonstrate substantial performance gain over conventional HD operation at the destination.