-
Gravitational wave interferometers are complex instruments, requiring years
of commissioning to achieve the required sensitivities for the detection of
gravitational waves, of order 10^-21 in dimensionless detector strain, in the
tens of Hz to several kHz frequency band. Investigations carried out by the
GEO600 detector characterisation group have shown that detector
characterisation techniques are useful when planning for commissioning work. At
the time of writing, GEO600 is the only large scale laser interferometer
currently in operation running with a high duty factor, 70%, limited chiefly by
the time spent commissioning the detector. The number of observable
gravitational wave sources scales as the product of the volume of space to
which the detector is sensitive and the observation time, so the goal of
commissioning is to improve the detector sensitivity with the least possible
detector down time. We demonstrate a method for increasing the number of
sources observable by such a detector, by assessing the severity of
non-astrophysical noise contaminations to efficiently guide commissioning. This
method will be particularly useful in the early stages and during the initial
science runs of the aLIGO and adVirgo detectors, as they are brought up to
design performance.
-
We report a search for gravitational waves from the inspiral, merger and
ringdown of binary black holes (BBH) with total mass between 25 and 100 solar
masses, in data taken at the LIGO and Virgo observatories between July 7, 2009
and October 20, 2010. The maximum sensitive distance of the detectors over this
period for a (20,20) Msun coalescence was 300 Mpc. No gravitational wave
signals were found. We thus report upper limits on the astrophysical
coalescence rates of BBH as a function of the component masses for non-spinning
components, and also evaluate the dependence of the search sensitivity on
component spins aligned with the orbital angular momentum. We find an upper
limit at 90% confidence on the coalescence rate of BBH with non-spinning
components of mass between 19 and 28 Msun of 3.3 \times 10^-7 mergers /Mpc^3
/yr.
-
A widely used assumption within the gravitational-wave community has so far
been that a test mass acts like a rigid body for frequencies in the detection
band, i.e. for frequencies far below the first internal resonance. In this
article we demonstrate that localized forces, applied for example by a photon
pressure actuator, can result in a non-negligible elastic deformation of the
test masses. For a photon pressure actuator setup used in the gravitational
wave detector GEO600 we measured that this effect modifies the standard
response function by 10% at 1 kHz and about 100% at 2.5 kHz.
-
FINESSE is a software simulation that allows to compute the optical
properties of laser interferometers as they are used by the interferometric
gravitational-wave detectors today. It provides a fast and versatile tool which
has proven to be very useful during the design and the commissioning of
gravitational-wave detectors. The basic algorithm of FINESSE numerically
computes the light amplitudes inside an interferometer using Hermite-Gauss
modes in the frequency domain. In addition, FINESSE provides a number of
commands to easily generate and plot the most common signals like, for example,
power enhancement, error or control signals, transfer functions and
shot-noise-limited sensitivities.
Among the various simulation tools available to the gravitational wave
community today, FINESSE is the most advanced general optical simulation that
uses the frequency domain. It has been designed to allow general analysis of
user defined optical setups while being easy to install and easy to use.
-
Using one arm of the Michelson interferometer and the power recycling mirror
of the interferometric gravitational wave detector GEO600, we created a
Fabry-Perot cavity with a length of 1200 m. The main purpose of this experiment
was to gather first experience with the main optics, its suspensions and the
corresponding control systems. The residual displacement of a main mirror is
about 150 nm rms. By stabilising the length of the 1200 m long cavity to the
pre-stabilised laser beam we achieved an error point frequency noise of 0.1
mHz/sqrt(Hz) at 100 Hz Fourier frequency. In addition we demonstrated the
reliable performance of all included subsystems by several 10-hour-periods of
continuous stable operation. Thus the full frequency stabilisation scheme for
GEO600 was successfully tested.
-
Dual recycling is an advanced optical technique to enhance the
signal-to-noise ratio of laser interferometric gravitational wave detectors in
a limited bandwidth. To optimise the center of this band with respect to
Fourier frequencies of expected gravitational wave signals detuned dual
recycling has to be implemented. We demonstrated detuned dual recycling on a
fully suspended 30m prototype interferometer. A control scheme that allows to
tune the detector to different frequencies will be outlined. Good agreement
between the experimental results and numerical simulations has been achieved.
Gravitational wave interferometers are complex instruments, requiring years of commissioning to achieve the required sensitivities for the detection of gravitational waves, of order 10^-21 in dimensionless detector strain, in the tens of Hz to several kHz frequency band. Investigations carried out by the GEO600 detector characterisation group have shown that detector characterisation techniques are useful when planning for commissioning work. At the time of writing, GEO600 is the only large scale laser interferometer currently in operation running with a high duty factor, 70%, limited chiefly by the time spent commissioning the detector. The number of observable gravitational wave sources scales as the product of the volume of space to which the detector is sensitive and the observation time, so the goal of commissioning is to improve the detector sensitivity with the least possible detector down time. We demonstrate a method for increasing the number of sources observable by such a detector, by assessing the severity of non-astrophysical noise contaminations to efficiently guide commissioning. This method will be particularly useful in the early stages and during the initial science runs of the aLIGO and adVirgo detectors, as they are brought up to design performance.
We report a search for gravitational waves from the inspiral, merger and ringdown of binary black holes (BBH) with total mass between 25 and 100 solar masses, in data taken at the LIGO and Virgo observatories between July 7, 2009 and October 20, 2010. The maximum sensitive distance of the detectors over this period for a (20,20) Msun coalescence was 300 Mpc. No gravitational wave signals were found. We thus report upper limits on the astrophysical coalescence rates of BBH as a function of the component masses for non-spinning components, and also evaluate the dependence of the search sensitivity on component spins aligned with the orbital angular momentum. We find an upper limit at 90% confidence on the coalescence rate of BBH with non-spinning components of mass between 19 and 28 Msun of 3.3 \times 10^-7 mergers /Mpc^3 /yr.
A widely used assumption within the gravitational-wave community has so far been that a test mass acts like a rigid body for frequencies in the detection band, i.e. for frequencies far below the first internal resonance. In this article we demonstrate that localized forces, applied for example by a photon pressure actuator, can result in a non-negligible elastic deformation of the test masses. For a photon pressure actuator setup used in the gravitational wave detector GEO600 we measured that this effect modifies the standard response function by 10% at 1 kHz and about 100% at 2.5 kHz.