This work is on the Physics of the B Factories. Part A of this book contains
a brief description of the SLAC and KEK B Factories as well as their detectors,
BaBar and Belle, and data taking related issues. Part B discusses tools and
methods used by the experiments in order to obtain results. The results
themselves can be found in Part C.
Please note that version 3 on the archive is the auxiliary version of the
Physics of the B Factories book. This uses the notation alpha, beta, gamma for
the angles of the Unitarity Triangle. The nominal version uses the notation
phi_1, phi_2 and phi_3. Please cite this work as Eur. Phys. J. C74 (2014) 3026.
Magnetic properties in the quasi-one-dimensional organic salt (TMTTF)2SbF6
are investigated by 13C NMR under pressures. Antiferromagnetic phase transition
at ambient pressure (AFI) is confirmed. Charge-ordering is suppressed by
pressure and is not observed under 8 kbar. For 5 < P < 20 kbar, a sharp
spectrum and the rapid decrease of the spin-lattice relaxation rate 1/T1 were
observed below about 4 K, attributed to a spin-gap transition. Above 20 kbar,
extremely broadened spectrum and critical increase of 1/T1 were observed. This
indicates that the system enters into another antiferromagnetic phase (AFII)
under pressure. The slope of the antiferromagnetic phase transition temperature
T_AFII, dT_AFII/dP, is positive, while T_AFI decreases with pressure. The
magnetic moment is weakly incommensurate with the lattice at 30 kbar.
The Belle detector at the KEKB electron-positron collider has collected
almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an
upgrade of KEKB is under construction, to increase the luminosity by two orders
of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2
/s luminosity. To exploit the increased luminosity, an upgrade of the Belle
detector has been proposed. A new international collaboration Belle-II, is
being formed. The Technical Design Report presents physics motivation, basic
methods of the accelerator upgrade, as well as key improvements of the
Crab cavities have been installed in the KEKB B--Factory rings to compensate
the crossing angle at the collision point and thus increase luminosity. The
beam operation with crab crossing has been done since February 2007. This is
the first experience with such cavities in colliders or storage rings. The crab
cavities have been working without serious issues. While higher specific
luminosity than the geometrical gain has been achieved, further study is
necessary and under way to reach the prediction of simulation.
In order to double the positron injection rate into the KEKB ring, a
two-bunch acceleration scheme has been studied at the linac, in which bunches
separated by 96 ns are accelerated in 50 Hz. In this scheme the stabilization
of energy and orbit of each bunch is indispensable. Thus the beam energy and
orbit feedback systems have been upgraded.
Since beam characteristics are acquired through beam position monitors (BPM),
their read-out system was improved to meet two-bunch requirements. Combined
waveforms from BPM's were adjusted with delay cables avoiding overlaps and they
enabled simultaneous measurement of beam positions of two bunches.
The beam energies of two bunches were balanced by tuning rf pulse timings,
and the average energy was stabilized by adjusting the accelerating rf phases.
The average beam orbits were also stabilized. Slow feedback systems at the
injector section for charge and bunching stabilities are being planned as well.
These systems were used successfully in the test beams and will be employed in
the routine operation.
In the control system of the JAERI-KEK joint project (High Intensity Proton
Accelerator Facility), it is planned to employ network-based controllers such
as PLC's and measurement stations instead of using other field control
networks, since the network hardware and software can be standardized and they
have been successfully utilized in other accelerator control systems in KEK.
EPICS software support for those controllers was designed paying special
attention to robustness and has been implemented and applied for the
accelerator test stand. Basic functionalities were confirmed and miscellaneous
functions such as diagnosis of the software itself would be added.
Since many kinds of network-based equipment such as oscilloscopes have become
available recently, they are considered to be integrated as well. They may
enable more manageable controllers.
The current status of the control system for a new high intensity proton
accelerator, the JAERI-KEK Joint Project, is presented. The Phase 1 of the
Joint-Project has been approved and recently started its construction at JAERI
site at Tokai. The first beam commissioning is scheduled in 2006. In parallel
with it, a 60-MeV Linac is now being constructed at KEK site at Tsukuba for R&D
purpose. Recently the Project has officially decided to use the Experimental
Physics and Industrial Control System (EPICS). Under the EPICS environment, we
are challenging to implement the Ethernet/IP network for all communication,
even at the level of end-point controllers which are so far connected via a
field bus. In order to realize such a system, three new controllers (PLCs,
WE7000 stations and general-purpose Ethernet boards) are being developed. A
prototype EPICS driver for the PLCs works fine and is used to control the
ion-source at the KEK Linac.
KEK electron linac was upgraded to 8 GeV for the KEK B-Factory (KEKB)
project. During the commissioning of the upgraded linac, even continuing SOR
ring injections, we had achieved a primary electron beam with 10-nC (6.24 x
10^10) per bunch up to 3.7-GeV for positron generation. This could be
classified as one of the brightest S-band linac's.
Since the KEKB rings were completed in December 1998, those 3.5-GeV position
and 8-GeV electron beams have been injected with an excellent performance.
Moreover, we have succeeded in switching among the high-intensity beams for
KEKB and beams for two SOR rings with sufficient reproducibility.
After the commissioning of the KEKB ring started, we have launched a project
to stabilize the intensity and quality of the high-current beams furthermore,
and have accomplished it investigating every conceivable aspect.
The KEK 8-GeV electron / 3.5-GeV positron linac has been operated with very
different beam specifications for downstream rings, KEKB, PF and PF-AR. For the
reliable operation among these beam modes intelligent beam switching and beam
feedback systems have been developed and used since its commissioning.
A software panel is used to choose one of four beam modes and a switching
sequence is executed in about two minutes. Most items in a sequence are simple
operations followed by failure recoveries. The magnet standardization part
consumes most of the time. The sequence can be re-arranged easily by
accelerator operators. Linac beam modes are switched about fifty times a day
using this software.
In order to stabilize linac beam energy and orbits, as well as some
accelerator equipment, about thirty software beam feedback loops have been
installed. They have been utilized routinely in all beam modes, and have
improved its beam quality. Since its software interfaces are standardized, it
is easy to add new feedback loops simply defining monitors and actuators.