-
The prospect of pileup induced backgrounds at the High Luminosity LHC
(HL-LHC) has stimulated intense interest in developing technologies for charged
particle detection with accurate timing at high rates. The required accuracy
follows directly from the nominal interaction distribution within a bunch
crossing ($\sigma_z\sim5$ cm, $\sigma_t\sim170$ ps). A time resolution of the
order of 20-30 ps would lead to significant reduction of these backgrounds.
With this goal, we present a new detection concept called PICOSEC, which is
based on a "two-stage" Micromegas detector coupled to a Cherenkov radiator and
equipped with a photocathode. First results obtained with this new detector
yield a time resolution of 24 ps for 150 GeV muons, and 76 ps for single
photoelectrons.
-
The TOTEM experiment at the CERN LHC has measured elastic proton-proton
scattering at the centre-of-mass energy $\sqrt{s}$ = 8 TeV and four-momentum
transfers squared, |t|, from 6 x $10^{-4}$ GeV$^2$ to 0.2 GeV$^2$. Near the
lower end of the |t|-interval the differential cross-section is sensitive to
the interference between the hadronic and the electromagnetic scattering
amplitudes. This article presents the elastic cross-section measurement and the
constraints it imposes on the functional forms of the modulus and phase of the
hadronic elastic amplitude. The data exclude the traditional Simplified West
and Yennie interference formula that requires a constant phase and a purely
exponential modulus of the hadronic amplitude. For parametrisations of the
hadronic modulus with second- or third-order polynomials in the exponent, the
data are compatible with hadronic phase functions giving either central or
peripheral behaviour in the impact parameter picture of elastic scattering. In
both cases, the $\rho$-parameter is found to be 0.12 $\pm$ 0.03. The results
for the total hadronic cross-section are $\sigma_{tot}$ = (102.9 $\pm$ 2.3) mb
and (103.0 $\pm$ 2.3) mb for central and peripheral phase formulations,
respectively. Both are consistent with previous TOTEM measurements.
-
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been
utilised to assess and monitor the flatness of Gaseous Electron Multipliers
(GEM) foils. The setup layout and preliminary results are presented.
-
We present a novel application of Fiber Bragg Grating (FBG) sensors in the
construction and characterisation of Micro Pattern Gaseous Detector (MPGD),
with particular attention to the realisation of the largest triple (Gas
electron Multiplier) GEM chambers so far operated, the GE1/1 chambers of the
CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of
about 0.5 m2 active area each, employing three GEM foils per chamber, to be
installed in the forward region of the CMS endcap during the long shutdown of
LHC in 2108-2019. The large active area of each GE1/1 chamber consists of GEM
foils that are mechanically stretched in order to secure their flatness and the
consequent uniform performance of the GE1/1 chamber across its whole active
surface. So far FBGs have been used in high energy physics mainly as high
precision positioning and re-positioning sensors and as low cost, easy to
mount, low space consuming temperature sensors. FBGs are also commonly used for
very precise strain measurements in material studies. In this work we present a
novel use of FBGs as flatness and mechanical tensioning sensors applied to the
wide GEM foils of the GE1/1 chambers. A network of FBG sensors have been used
to determine the optimal mechanical tension applied and to characterise the
mechanical tension that should be applied to the foils. We discuss the results
of the test done on a full-sized GE1/1 final prototype, the studies done to
fully characterise the GEM material, how this information was used to define a
standard assembly procedure and possible future developments.
-
Graphene is a single layer of carbon atoms arranged in a honeycomb lattice
with remarkable mechanical and electrical properties. Regarded as the thinnest
and narrowest conductive mesh, it has drastically different transmission
behaviours when bombarded with electrons and ions in vacuum. This property, if
confirmed in gas, may be a definitive solution for the ion back-flow problem in
gaseous detectors. In order to ascertain this aspect, graphene layers of
dimensions of about 2x2cm$^2$, grown on a copper substrate, are transferred
onto a flat metal surface with holes, so that the graphene layer is freely
suspended. The graphene and the support are installed into a gaseous detector
equipped with a triple Gaseous Electron Multiplier (GEM), and the transparency
properties to electrons and ions are studied in gas as a function of the
electric fields. The techniques to produce the graphene samples are described,
and we report on preliminary tests of graphene-coated GEMs.
-
A comprehensive study, supported by systematic measurements and numerical
computations, of the intrinsic limits of multi-GEM detectors when exposed to
very high particle fluxes or operated at very large gains is presented. The
observed variations of the gain, of the ion back-flow, and of the pulse height
spectra are explained in terms of the effects of the spatial distribution of
positive ions and their movement throughout the amplification structure. The
intrinsic dynamic character of the processes involved imposes the use of a
non-standard simulation tool for the interpretation of the measurements.
Computations done with a Finite Element Analysis software reproduce the
observed behaviour of the detector. The impact of this detailed description of
the detector in extreme conditions is multiple: it clarifies some detector
behaviours already observed, it helps in defining intrinsic limits of the GEM
technology, and it suggests ways to extend them.
-
The TOTEM experiment has made a precise measurement of the elastic
proton-proton differential cross-section at the centre-of-mass energy sqrt(s) =
8 TeV based on a high-statistics data sample obtained with the beta* = 90
optics. Both the statistical and systematic uncertainties remain below 1%,
except for the t-independent contribution from the overall normalisation. This
unprecedented precision allows to exclude a purely exponential differential
cross-section in the range of four-momentum transfer squared 0.027 < |t| < 0.2
GeV^2 with a significance greater than 7 sigma. Two extended parametrisations,
with quadratic and cubic polynomials in the exponent, are shown to be well
compatible with the data. Using them for the differential cross-section
extrapolation to t = 0, and further applying the optical theorem, yields total
cross-section estimates of (101.5 +- 2.1) mb and (101.9 +- 2.1) mb,
respectively, in agreement with previous TOTEM measurements.
-
Graphene is a single layer of carbon atoms arranged in a honeycomb lattice
with remarkable mechanical, electrical and optical properties. For the first
time graphene layers suspended on copper meshes were installed into a gas
detector equipped with a gaseous electron multiplier. Measurements of low
energy electron and ion transfer through graphene were conducted. In this paper
we describe the sample preparation for suspended graphene layers, the testing
procedures and we discuss the preliminary results followed by a prospect of
further applications.
-
Gas Electron Multiplier (GEM) technology is being considered for the forward
muon upgrade of the CMS experiment in Phase 2 of the CERN LHC. Its first
implementation is planned for the GE1/1 system in the $1.5 < \mid\eta\mid <
2.2$ region of the muon endcap mainly to control muon level-1 trigger rates
after the second long LHC shutdown. A GE1/1 triple-GEM detector is read out by
3,072 radial strips with 455 $\mu$rad pitch arranged in eight $\eta$-sectors.
We assembled a full-size GE1/1 prototype of 1m length at Florida Tech and
tested it in 20-120 GeV hadron beams at Fermilab using Ar/CO$_{2}$ 70:30 and
the RD51 scalable readout system. Four small GEM detectors with 2-D readout and
an average measured azimuthal resolution of 36 $\mu$rad provided precise
reference tracks. Construction of this largest GEM detector built to-date is
described. Strip cluster parameters, detection efficiency, and spatial
resolution are studied with position and high voltage scans. The plateau
detection efficiency is [97.1 $\pm$ 0.2 (stat)]\%. The azimuthal resolution is
found to be [123.5 $\pm$ 1.6 (stat)] $\mu$rad when operating in the center of
the efficiency plateau and using full pulse height information. The resolution
can be slightly improved by $\sim$ 10 $\mu$rad when correcting for the bias due
to discrete readout strips. The CMS upgrade design calls for readout
electronics with binary hit output. When strip clusters are formed
correspondingly without charge-weighting and with fixed hit thresholds, a
position resolution of [136.8 $\pm$ 2.5 stat] $\mu$rad is measured, consistent
with the expected resolution of strip-pitch/$\sqrt{12}$ = 131.3 $\mu$rad. Other
$\eta$-sectors of the detector show similar response and performance.
-
The pseudorapidity density of charged particles dN(ch)/deta is measured by
the TOTEM experiment in pp collisions at sqrt(s) = 8 TeV within the range 3.9 <
eta < 4.7 and -6.95 < eta < -6.9. Data were collected in a low intensity LHC
run with collisions occurring at a distance of 11.25 m from the nominal
interaction point. The data sample is expected to include 96-97\% of the
inelastic proton-proton interactions. The measurement reported here considers
charged particles with p_T > 0 MeV/c, produced in inelastic interactions with
at least one charged particle in -7 < eta < -6 or 3.7 < eta <4.8 . The
dN(ch)/deta has been found to decrease with |eta|, from 5.11 +- 0.73 at eta =
3.95 to 1.81 +- 0.56 at eta= - 6.925. Several MC generators are compared to the
data and are found to be within the systematic uncertainty of the measurement.
-
Precise knowledge of the beam optics at the LHC is crucial to fulfil the
physics goals of the TOTEM experiment, where the kinematics of the scattered
protons is reconstructed with the near-beam telescopes -- so-called Roman Pots
(RP). Before being detected, the protons' trajectories are influenced by the
magnetic fields of the accelerator lattice. Thus precise understanding of the
proton transport is of key importance for the experiment. A novel method of
optics evaluation is proposed which exploits kinematical distributions of
elastically scattered protons observed in the RPs. Theoretical predictions, as
well as Monte Carlo studies, show that the residual uncertainty of this optics
estimation method is smaller than 0.25 percent.
-
The TOTEM Experiment is designed to measure the total proton-proton
cross-section with the luminosity-independent method and to study elastic and
diffractive pp scattering at the LHC. To achieve optimum forward coverage for
charged particles emitted by the pp collisions in the interaction point IP5,
two tracking telescopes, T1 and T2, are installed on each side of the IP in the
pseudorapidity region 3.1 < = |eta | < = 6.5, and special movable beam-pipe
insertions - called Roman Pots (RP) - are placed at distances of +- 147 m and
+- 220 m from IP5. This article describes in detail the working of the TOTEM
detector to produce physics results in the first three years of operation and
data taking at the LHC.
-
The first double diffractive cross-section measurement in the very forward
region has been carried out by the TOTEM experiment at the LHC with
center-of-mass energy of sqrt(s)=7 TeV. By utilizing the very forward TOTEM
tracking detectors T1 and T2, which extend up to |eta|=6.5, a clean sample of
double diffractive pp events was extracted. From these events, we measured the
cross-section sigma_DD =(116 +- 25) mub for events where both diffractive
systems have 4.7 <|eta|_min < 6.5 .
-
The CMS GEM collaboration is considering Gas Electron Multipliers (GEMs) for
upgrading the CMS forward muon system in the 1.5<|eta|<2.4 endcap region. GEM
detectors can provide precision tracking and fast trigger information. They
would improve the CMS muon trigger and muon momentum resolution and provide
missing redundancy in the high-eta region. Employing a new faster construction
and assembly technique, we built four full-scale Triple-GEM muon detectors for
the inner ring of the first muon endcap station. We plan to install these or
further improved versions in CMS during the first long LHC shutdown in 2013/14
for continued testing. These detectors are designed for the stringent rate and
resolution requirements in the increasingly hostile environments expected at
CMS after the second long LHC shutdown in 2018/19. The new prototypes were
studied in muon/pion beams at the CERN SPS. We discuss our experience with
constructing the new full-scale production prototypes and present preliminary
performance results from the beam test. We also tested smaller Triple-GEM
prototypes with zigzag readout strips with 2 mm pitch in these beams and
measured a spatial resolution of 73 microns. This readout offers a potential
reduction of channel count and consequently electronics cost for this system
while maintaining high spatial resolution.
-
The TOTEM experiment has measured the charged particle pseudorapidity density
dN_{ch}/deta in pp collisions at sqrt{s} = 7 TeV for 5.3<|eta|<6.4 in events
with at least one charged particle with transverse momentum above 40 MeV/c in
this pseudorapidity range. This extends the analogous measurement performed by
the other LHC experiments to the previously unexplored forward eta region. The
measurement refers to more than 99% of non-diffractive processes and to single
and double diffractive processes with diffractive masses above ~3.4 GeV/c^2,
corresponding to about 95% of the total inelastic cross-section. The
dN_{ch}/deta has been found to decrease with |eta|, from 3.84 pm 0.01(stat) pm
0.37(syst) at |eta| = 5.375 to 2.38 pm 0.01(stat) pm 0.21(syst) at |eta| =
6.375. Several MC generators have been compared to data; none of them has been
found to fully describe the measurement.
-
Proton-proton elastic scattering has been measured by the TOTEM experiment at
the CERN Large Hadron Collider at $\sqrt{s} = 7 $ TeV in special runs with the
Roman Pot detectors placed as close to the outgoing beam as seven times the
transverse beam size. The differential cross-section measurements are reported
in the |t|-range of 0.36 to 2.5 GeV^2. Extending the range of data to low t
values from 0.02 to 0.33 GeV^2,and utilizing the luminosity measurements of
CMS, the total proton-proton cross section at sqrt(s) = 7 TeV is measured to be
(98.3 +- 0.2(stat) +- 2.8(syst)) mb.
-
At present, part of the forward RPC muon system of the CMS detector at the
CERN LHC remains uninstrumented in the high-\eta region. An international
collaboration is investigating the possibility of covering the 1.6 < |\eta| <
2.4 region of the muon endcaps with large-area triple-GEM detectors. Given
their good spatial resolution, high rate capability, and radiation hardness,
these micro-pattern gas detectors are an appealing option for simultaneously
enhancing muon tracking and triggering capabilities in a future upgrade of the
CMS detector. A general overview of this feasibility study will be presented.
The design and construction of small (10\times10 cm2) and full-size trapezoidal
(1\times0.5 m2) triple-GEM prototypes will be described. During detector
assembly, different techniques for stretching the GEM foils were tested.
Results from measurements with x-rays and from test beam campaigns at the CERN
SPS will be shown for the small and large prototypes. Preliminary simulation
studies on the expected muon reconstruction and trigger performances of this
proposed upgraded muon system will be reported.
-
Gas Electron Multipliers (GEM) are an interesting technology under
consideration for the future upgrade of the forward region of the CMS muon
system, specifically in the $1.6<| \eta |<2.4$ endcap region. With a
sufficiently fine segmentation GEMs can provide precision tracking as well as
fast trigger information. The main objective is to contribute to the
improvement of the CMS muon trigger. The construction of large-area GEM
detectors is challenging both from the technological and production aspects. In
view of the CMS upgrade we have designed and built the largest full-size
Triple-GEM muon detector, which is able to meet the stringent requirements
given the hostile environment at the high-luminosity LHC. Measurements were
performed during several test beam campaigns at the CERN SPS in 2010 and 2011.
The main issues under study are efficiency, spatial resolution and timing
performance with different inter-electrode gap configurations and gas mixtures.
In this paper results of the performance of the prototypes at the beam tests
will be discussed.
-
Proton-proton elastic scattering has been measured by the TOTEM experiment at
the CERN Large Hadron Collider at {\surd}s = 7 TeV in dedicated runs with the
Roman Pot detectors placed as close as seven times the transverse beam size
(sbeam) from the outgoing beams. After careful study of the accelerator optics
and the detector alignment, |t|, the square of four-momentum transferred in the
elastic scattering process, has been determined with an uncertainty of d t =
0.1GeV p|t|. In this letter, first results of the differential cross section
are presented covering a |t|-range from 0.36 to 2.5GeV2. The differential
cross-section in the range 0.36 < |t| < 0.47 GeV2 is described by an
exponential with a slope parameter B = (23.6{\pm}0.5stat {\pm}0.4syst)GeV-2,
followed by a significant diffractive minimum at |t| =
(0.53{\pm}0.01stat{\pm}0.01syst)GeV2. For |t|-values larger than ~ 1.5GeV2, the
cross-section exhibits a power law behaviour with an exponent of -7.8_\pm}
0.3stat{\pm}0.1syst. When compared to predictions based on the different
available models, the data show a strong discriminative power despite the small
t-range covered.
-
TOTEM has measured the differential cross-section for elastic proton-proton
scattering at the LHC energy of {\srud}s = 7TeV analysing data from a short run
with dedicated large {\beta} * optics. A single exponential fit with a slope B
= (20:1{\pm}0:2stat {\pm}0:3syst)GeV-2 describes the range of the four-momentum
transfer squared |t| from 0.02 to 0.33 GeV2. After the extrapolation to |t| =
0, a total elastic scattering cross-section of (24:8{\pm}0:2stat {\pm}1:2syst)
mb was obtained. Applying the optical theorem and using the luminosity
measurement from CMS, a total proton-proton cross-section of (98:3{\pm}0:2stat
{\pm}2:8syst) mb was deduced which is in good agreement with the expectation
from the overall fit of previously measured data over a large range of
center-of-mass energies. From the total and elastic pp cross-section
measurements, an inelastic pp cross-section of (73:5{\pm}0:6stat +1:8 -1:3
syst) mb was inferred. PACS 13.60.Hb: Total and inclusive cross sections
-
The first physics results from the TOTEM experiment are here reported,
concerning the measurements of the total, differential elastic, elastic and
inelastic pp cross-section at the LHC energy of $\sqrt{s}$ = 7 TeV, obtained
using the luminosity measurement from CMS. A preliminary measurement of the
forward charged particle $\eta$ distribution is also shown.
-
The muon detection system of the Compact Muon Solenoid experiment at the CERN
Large Hadron Collider is based on different technologies for muon tracking and
triggering. In particular, the muon system in the endcap disks of the detector
consists of Resistive Plate Chambers for triggering and Cathode Strip Chambers
for tracking. At present, the endcap muon system is only partially instrumented
with the very forward detector region remaining uncovered. In view of a
possible future extension of the muon endcap system, we report on a feasibility
study on the use of Micro-Pattern Gas Detectors, in particular Gas Electron
Multipliers, for both muon triggering and tracking. Results on the construction
and characterization of small tripleGas Electron Multiplier prototype detectors
are presented.
-
In view of a possible extension of the forward CMS muon detector system and
future LHC luminosity upgrades, Micro-Pattern Gas Detectors (MPGDs) are an
appealing technology. They can simultaneously provide precision tracking and
fast trigger information, as well as sufficiently fine segmentation to cope
with high particle rates in the high-eta region at LHC and its future upgrades.
We report on the design and construction of a full-size prototype for the CMS
endcap system, the largest Triple-GEM detector built to-date. We present
details on the 3D modeling of the detector geometry, the implementation of the
readout strips and electronics, and the detector assembly procedure.
-
2nd workshop on the implications of HERA for LHC physics. Working groups:
Parton Density Functions Multi-jet final states and energy flows Heavy quarks
(charm and beauty) Diffraction Cosmic Rays Monte Carlos and Tools
-
The TOTEM experiment at the LHC measures the total proton-proton cross
section with the luminosity-independent method and the elastic proton-proton
cross-section over a wide |t|-range. It also performs a comprehensive study of
diffraction, spanning from cross-section measurements of individual diffractive
processes to the analysis of their event topologies. Hard diffraction will be
studied in collaboration with CMS taking advantage of the large common rapidity
coverage for charged and neutral particle detection and the large variety of
trigger possibilities even at large luminosities. TOTEM will take data under
all LHC beam conditions including standard high luminosity runs to maximize its
physics reach. This contribution describes the main features of the TOTEM
physics programme including measurements to be made in the early LHC runs. In
addition, a novel scheme to extend the diffractive proton acceptance for high
luminosity runs by installing proton detectors at IP3 is described.