-
During the shutdown of the CERN Large Hadron Collider in 2013-2014, an
additional pixel layer was installed between the existing Pixel detector of the
ATLAS experiment and a new, smaller radius beam pipe. The motivation for this
new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the
robustness and performance of the ATLAS tracking system, given the higher
instantaneous and integrated luminosities realised following the shutdown.
Because of the extreme radiation and collision rate environment, several new
radiation-tolerant sensor and electronic technologies were utilised for this
layer. This paper reports on the IBL construction and integration prior to its
operation in the ATLAS detector.
-
We report on the cryogenic characterization of Red Green Blue - High Density
(RGB-HD) SiPMs developed at Fondazione Bruno Kessler (FBK) as part of the
DarkSide program of dark matter searches with liquid argon time projection
chambers. A dedicated setup was used to measure the primary dark noise, the
correlated noise, and the gain of the SiPMs at varying temperatures. A
custom-made data acquisition system and analysis software were used to
precisely characterize these parameters. We demonstrate that FBK RGB-HD SiPMs
with low quenching resistance (RGB-HD-LR$_q$) can be operated from 40 K to 300
K with gains in the range $10^5$ to $10^6$ and noise rates on the order of a
few Hz/mm$^2$.
-
Building on the successful experience in operating the DarkSide-50 detector,
the DarkSide Collaboration is going to construct DarkSide-20k, a direct WIMP
search detector using a two-phase Liquid Argon Time Projection Chamber (LArTPC)
with an active (fiducial) mass of 23 t (20 t). The DarkSide-20k LArTPC will be
deployed within a shield/veto with a spherical Liquid Scintillator Veto (LSV)
inside a cylindrical Water Cherenkov Veto (WCV). Operation of DarkSide-50
demonstrated a major reduction in the dominant $^{39}$Ar background when using
argon extracted from an underground source, before applying pulse shape
analysis. Data from DarkSide-50, in combination with MC simulation and
analytical modeling, shows that a rejection factor for discrimination between
electron and nuclear recoils of $\gt3\times10^9$ is achievable. This, along
with the use of the veto system, is the key to unlocking the path to large
LArTPC detector masses, while maintaining an "instrumental background-free"
experiment, an experiment in which less than 0.1 events (other than
$\nu$-induced nuclear recoils) is expected to occur within the WIMP search
region during the planned exposure. DarkSide-20k will have ultra-low
backgrounds than can be measured in situ. This will give sensitivity to
WIMP-nucleon cross sections of $1.2\times10^{-47}$ cm$^2$ ($1.1\times10^{-46}$
cm$^2$) for WIMPs of $1$ TeV$/c^2$ ($10$ TeV$/c^2$) mass, to be achieved during
a 5 yr run producing an exposure of 100 t yr free from any instrumental
background. DarkSide-20k could then extend its operation to a decade,
increasing the exposure to 200 t yr, reaching a sensitivity of
$7.4\times10^{-48}$ cm$^2$ ($6.9\times10^{-47}$ cm$^2$) for WIMPs of $1$
TeV$/c^2$ ($10$ TeV$/c^2$) mass.
-
We present the results of a detailed simulation of the artificial retina
pattern-recognition algorithm, designed to reconstruct events with hundreds of
charged-particle tracks in pixel and silicon detectors at LHCb with LHC
crossing frequency of $40\,\rm MHz$. Performances of the artificial retina
algorithm are assessed using the official Monte Carlo samples of the LHCb
experiment. We found performances for the retina pattern-recognition algorithm
comparable with the full LHCb reconstruction algorithm.
-
We present results of an R&D study for a specialized processor capable of
precisely reconstructing, in pixel detectors, hundreds of charged-particle
tracks from high-energy collisions at 40 MHz rate. We apply a highly parallel
pattern-recognition algorithm, inspired by studies of the processing of visual
images by the brain as it happens in nature, and describe in detail an
efficient hardware implementation in high-speed, high-bandwidth FPGA devices.
This is the first detailed demonstration of reconstruction of offline-quality
tracks at 40 MHz and makes the device suitable for processing Large Hadron
Collider events at the full crossing frequency.
-
We present the results of an R&D study for a specialized processor capable of
precisely reconstructing events with hundreds of charged-particle tracks in
pixel and silicon strip detectors at $40\,\rm MHz$, thus suitable for
processing LHC events at the full crossing frequency. For this purpose we
design and test a massively parallel pattern-recognition algorithm, inspired to
the current understanding of the mechanisms adopted by the primary visual
cortex of mammals in the early stages of visual-information processing. The
detailed geometry and charged-particle's activity of a large tracking detector
are simulated and used to assess the performance of the artificial retina
algorithm. We find that high-quality tracking in large detectors is possible
with sub-microsecond latencies when the algorithm is implemented in modern,
high-speed, high-bandwidth FPGA devices.
-
We report on the R\&D for a first prototype of a silicon tracker based on an
alternative approach for fast track finding. The working principle is inspired
from neurobiology, in particular by the processing of visual images by the
brain as it happens in nature. It is based on extensive parallelisation of data
distribution and pattern recognition. In this work we present the design of a
practical device that consists of a telescope based on single-sided silicon
detectors; we describe the data acquisition system and the implementation of
the track finding algorithms using available digital logic of commercial FPGA
devices. Tracking performance and trigger capabilities of the device are
discussed along with perspectives for future applications.
-
We present the results of an R&D study of a specialized processor capable of
precisely reconstructing events with hundreds of charged-particle tracks in
pixel detectors at 40 MHz, thus suitable for processing LHC events at the full
crossing frequency. For this purpose we design and test a massively parallel
pattern-recognition algorithm, inspired by studies of the processing of visual
images by the brain as it happens in nature. We find that high-quality tracking
in large detectors is possible with sub-$\mu$s latencies when this algorithm is
implemented in modern, high-speed, high-bandwidth FPGA devices. This opens a
possibility of making track reconstruction happen transparently as part of the
detector readout.
-
The radiation hardness of commercial Silicon Carbide and Gallium Nitride
power MOSFETs is presented in this paper, for Total Ionizing Dose effects and
Single Event Effects, under gamma, neutrons, protons and heavy ions. Similar
tests are discussed for commercial DC-DC converters, also tested in operation
under magnetic field.
-
In this Technical Design Report (TDR) we describe the SuperB detector that
was to be installed on the SuperB e+e- high luminosity collider. The SuperB
asymmetric collider, which was to be constructed on the Tor Vergata campus near
the INFN Frascati National Laboratory, was designed to operate both at the
Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1}
and at the tau/charm production threshold with a luminosity of 10^{35}
cm^{-2}s^{-1}. This high luminosity, producing a data sample about a factor 100
larger than present B Factories, would allow investigation of new physics
effects in rare decays, CP Violation and Lepton Flavour Violation. This
document details the detector design presented in the Conceptual Design Report
(CDR) in 2007. The R&D and engineering studies performed to arrive at the full
detector design are described, and an updated cost estimate is presented.
A combination of a more realistic cost estimates and the unavailability of
funds due of the global economic climate led to a formal cancelation of the
project on Nov 27, 2012.
-
A new method for calibrating the hadron response of a segmented calorimeter
is developed and successfully applied to beam test data. It is based on a
principal component analysis of energy deposits in the calorimeter layers,
exploiting longitudinal shower development information to improve the measured
energy resolution. Corrections for invisible hadronic energy and energy lost in
dead material in front of and between the calorimeters of the ATLAS experiment
were calculated with simulated Geant4 Monte Carlo events and used to
reconstruct the energy of pions impinging on the calorimeters during the 2004
Barrel Combined Beam Test at the CERN H8 area. For pion beams with energies
between 20 GeV and 180 GeV, the particle energy is reconstructed within 3% and
the energy resolution is improved by between 11% and 25% compared to the
resolution at the electromagnetic scale.
-
A detailed study is presented of the expected performance of the ATLAS
detector. The reconstruction of tracks, leptons, photons, missing energy and
jets is investigated, together with the performance of b-tagging and the
trigger. The physics potential for a variety of interesting physics processes,
within the Standard Model and beyond, is examined. The study comprises a series
of notes based on simulations of the detector and physics processes, with
particular emphasis given to the data expected from the first years of
operation of the LHC at CERN.
-
A small set of final prototypes of the ATLAS Inner Detector silicon tracker
(Pixel and SCT) were used to take data during the 2004 Combined Test Beam. Data
were collected from runs with beams of different flavour (electrons, pions,
muons and photons) with a momentum range of 2 to 180 GeV/c. Four independent
methods were used to align the silicon modules. The corrections obtained were
validated using the known momenta of the beam particles and were shown to yield
consistent results among the different alignment approaches. From the residual
distributions, it is concluded that the precision attained in the alignment of
the silicon modules is of the order of 5 micrometers in their most precise
coordinate.
We report on the cryogenic characterization of Red Green Blue - High Density (RGB-HD) SiPMs developed at Fondazione Bruno Kessler (FBK) as part of the DarkSide program of dark matter searches with liquid argon time projection chambers. A dedicated setup was used to measure the primary dark noise, the correlated noise, and the gain of the SiPMs at varying temperatures. A custom-made data acquisition system and analysis software were used to precisely characterize these parameters. We demonstrate that FBK RGB-HD SiPMs with low quenching resistance (RGB-HD-LR$_q$) can be operated from 40 K to 300 K with gains in the range $10^5$ to $10^6$ and noise rates on the order of a few Hz/mm$^2$.
Building on the successful experience in operating the DarkSide-50 detector, the DarkSide Collaboration is going to construct DarkSide-20k, a direct WIMP search detector using a two-phase Liquid Argon Time Projection Chamber (LArTPC) with an active (fiducial) mass of 23 t (20 t). The DarkSide-20k LArTPC will be deployed within a shield/veto with a spherical Liquid Scintillator Veto (LSV) inside a cylindrical Water Cherenkov Veto (WCV). Operation of DarkSide-50 demonstrated a major reduction in the dominant $^{39}$Ar background when using argon extracted from an underground source, before applying pulse shape analysis. Data from DarkSide-50, in combination with MC simulation and analytical modeling, shows that a rejection factor for discrimination between electron and nuclear recoils of $\gt3\times10^9$ is achievable. This, along with the use of the veto system, is the key to unlocking the path to large LArTPC detector masses, while maintaining an "instrumental background-free" experiment, an experiment in which less than 0.1 events (other than $\nu$-induced nuclear recoils) is expected to occur within the WIMP search region during the planned exposure. DarkSide-20k will have ultra-low backgrounds than can be measured in situ. This will give sensitivity to WIMP-nucleon cross sections of $1.2\times10^{-47}$ cm$^2$ ($1.1\times10^{-46}$ cm$^2$) for WIMPs of $1$ TeV$/c^2$ ($10$ TeV$/c^2$) mass, to be achieved during a 5 yr run producing an exposure of 100 t yr free from any instrumental background. DarkSide-20k could then extend its operation to a decade, increasing the exposure to 200 t yr, reaching a sensitivity of $7.4\times10^{-48}$ cm$^2$ ($6.9\times10^{-47}$ cm$^2$) for WIMPs of $1$ TeV$/c^2$ ($10$ TeV$/c^2$) mass.
We present the results of a detailed simulation of the artificial retina pattern-recognition algorithm, designed to reconstruct events with hundreds of charged-particle tracks in pixel and silicon detectors at LHCb with LHC crossing frequency of $40\,\rm MHz$. Performances of the artificial retina algorithm are assessed using the official Monte Carlo samples of the LHCb experiment. We found performances for the retina pattern-recognition algorithm comparable with the full LHCb reconstruction algorithm.
We present results of an R&D study for a specialized processor capable of precisely reconstructing, in pixel detectors, hundreds of charged-particle tracks from high-energy collisions at 40 MHz rate. We apply a highly parallel pattern-recognition algorithm, inspired by studies of the processing of visual images by the brain as it happens in nature, and describe in detail an efficient hardware implementation in high-speed, high-bandwidth FPGA devices. This is the first detailed demonstration of reconstruction of offline-quality tracks at 40 MHz and makes the device suitable for processing Large Hadron Collider events at the full crossing frequency.
We present the results of an R&D study for a specialized processor capable of precisely reconstructing events with hundreds of charged-particle tracks in pixel and silicon strip detectors at $40\,\rm MHz$, thus suitable for processing LHC events at the full crossing frequency. For this purpose we design and test a massively parallel pattern-recognition algorithm, inspired to the current understanding of the mechanisms adopted by the primary visual cortex of mammals in the early stages of visual-information processing. The detailed geometry and charged-particle's activity of a large tracking detector are simulated and used to assess the performance of the artificial retina algorithm. We find that high-quality tracking in large detectors is possible with sub-microsecond latencies when the algorithm is implemented in modern, high-speed, high-bandwidth FPGA devices.
We report on the R\&D for a first prototype of a silicon tracker based on an alternative approach for fast track finding. The working principle is inspired from neurobiology, in particular by the processing of visual images by the brain as it happens in nature. It is based on extensive parallelisation of data distribution and pattern recognition. In this work we present the design of a practical device that consists of a telescope based on single-sided silicon detectors; we describe the data acquisition system and the implementation of the track finding algorithms using available digital logic of commercial FPGA devices. Tracking performance and trigger capabilities of the device are discussed along with perspectives for future applications.
We present the results of an R&D study of a specialized processor capable of precisely reconstructing events with hundreds of charged-particle tracks in pixel detectors at 40 MHz, thus suitable for processing LHC events at the full crossing frequency. For this purpose we design and test a massively parallel pattern-recognition algorithm, inspired by studies of the processing of visual images by the brain as it happens in nature. We find that high-quality tracking in large detectors is possible with sub-$\mu$s latencies when this algorithm is implemented in modern, high-speed, high-bandwidth FPGA devices. This opens a possibility of making track reconstruction happen transparently as part of the detector readout.
The radiation hardness of commercial Silicon Carbide and Gallium Nitride power MOSFETs is presented in this paper, for Total Ionizing Dose effects and Single Event Effects, under gamma, neutrons, protons and heavy ions. Similar tests are discussed for commercial DC-DC converters, also tested in operation under magnetic field.
In this Technical Design Report (TDR) we describe the SuperB detector that was to be installed on the SuperB e+e- high luminosity collider. The SuperB asymmetric collider, which was to be constructed on the Tor Vergata campus near the INFN Frascati National Laboratory, was designed to operate both at the Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1} and at the tau/charm production threshold with a luminosity of 10^{35} cm^{-2}s^{-1}. This high luminosity, producing a data sample about a factor 100 larger than present B Factories, would allow investigation of new physics effects in rare decays, CP Violation and Lepton Flavour Violation. This document details the detector design presented in the Conceptual Design Report (CDR) in 2007. The R&D and engineering studies performed to arrive at the full detector design are described, and an updated cost estimate is presented. A combination of a more realistic cost estimates and the unavailability of funds due of the global economic climate led to a formal cancelation of the project on Nov 27, 2012.
A new method for calibrating the hadron response of a segmented calorimeter is developed and successfully applied to beam test data. It is based on a principal component analysis of energy deposits in the calorimeter layers, exploiting longitudinal shower development information to improve the measured energy resolution. Corrections for invisible hadronic energy and energy lost in dead material in front of and between the calorimeters of the ATLAS experiment were calculated with simulated Geant4 Monte Carlo events and used to reconstruct the energy of pions impinging on the calorimeters during the 2004 Barrel Combined Beam Test at the CERN H8 area. For pion beams with energies between 20 GeV and 180 GeV, the particle energy is reconstructed within 3% and the energy resolution is improved by between 11% and 25% compared to the resolution at the electromagnetic scale.
A small set of final prototypes of the ATLAS Inner Detector silicon tracker (Pixel and SCT) were used to take data during the 2004 Combined Test Beam. Data were collected from runs with beams of different flavour (electrons, pions, muons and photons) with a momentum range of 2 to 180 GeV/c. Four independent methods were used to align the silicon modules. The corrections obtained were validated using the known momenta of the beam particles and were shown to yield consistent results among the different alignment approaches. From the residual distributions, it is concluded that the precision attained in the alignment of the silicon modules is of the order of 5 micrometers in their most precise coordinate.