-
The CERN-Latin-American School of High-Energy Physics is intended to give
young physicists an introduction to the theoretical aspects of recent advances
in elementary particle physics. These proceedings contain lecture notes on the
Standard Model of electroweak interactions, flavour physics, neutrino physics,
Higgs physics, new physics beyond the standard model, quantum chromodynamics
under extreme conditions, cosmology, an introduction to experimental facilities
at the high-energy frontier, and practical statistics for particle physicists.
-
The European School of High-Energy Physics is intended to give young
physicists an introduction to the the- oretical aspects of recent advances in
elementary particle physics. These proceedings contain lecture notes on the
theory of quantum chromodynamics, Higgs physics, Flavour physics and CP
violation, and Supersymmetry.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of
construction steel. The flux return yoke consists of five dodecagonal
three-layered barrel wheels and four end-cap disks at each end comprised of
steel blocks up to 620 mm thick, which serve as the absorber plates of the muon
detection system. To measure the field in and around the steel, a system of 22
flux loops and 82 3-D Hall sensors is installed on the return yoke blocks. A
TOSCA 3-D model of the CMS magnet is developed to describe the magnetic field
everywhere outside the tracking volume that was measured with the field-mapping
machine. The voltages induced in the flux loops by the magnetic flux changing
during the CMS magnet standard ramps down are measured with six 16-bit DAQ
modules. The off-line integration of the induced voltages reconstructs the
magnetic flux density in the yoke steel blocks at the operational magnet
current of 18.164 kA. The results of the flux loop measurements during three
magnet ramps down are presented and discussed.
-
The European School of High-Energy Physics is intended to give young
physicists an introduction to the theoretical aspects of recent advances in
elementary particle physics. These proceedings contain lecture notes on the
Standard Model of electroweak interactions, quantum chromodynamics, Higgs
physics, physics beyond the Standard Model, flavour physics, and practical
statistics for particle physicists.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of
construction steel. The return yoke consists of five dodecagonal three-layered
barrel wheels and four end-cap disks at each end comprised of steel blocks up
to 620 mm thick, which serve as the absorber plates of the muon detection
system. To measure the field in and around the steel, a system of 22 flux loops
and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D
model of the CMS magnet is developed to describe the magnetic field everywhere
outside the tracking volume measured with the field-mapping machine. The
magnetic field description is compared with the measurements and discussed.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of
construction steel. The return yoke consists of five dodecagonal three-layered
barrel wheels and four end-cap disks at each end comprised of steel blocks up
to 620 mm thick, which serve as the absorber plates of the muon detection
system. To measure the field in and around the steel, a system of 22 flux loops
and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D
model of the CMS magnet is developed to describe the magnetic field everywhere
outside the tracking volume measured with the field-mapping machine. The first
attempt is made to measure the magnetic flux density in the steel blocks of the
CMS magnet yoke using the standard magnet discharge with the current ramp down
speed of 1.5 A/s.
-
The CERN - Latin-American School of High-Energy Physics is intended to give
young physicists an introduction to the theoretical aspects of recent advances
in elementary particle physics. These proceedings contain lecture notes on the
Standard Model of electroweak interactions, quantum chromodynamics, flavour
physics, quantum chromodynamics under extreme conditions, cosmic-ray physics,
cosmology, recent highlights of LHC results, practical statistics for particle
physicists and a short introduction to the principles of particle physics
instrumentation.
-
A joint measurement is presented of the branching fractions
$B^0_s\to\mu^+\mu^-$ and $B^0\to\mu^+\mu^-$ in proton-proton collisions at the
LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at
a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis
produces the first observation of the $B^0_s\to\mu^+\mu^-$ decay, with a
statistical significance exceeding six standard deviations, and the best
measurement of its branching fraction so far. Furthermore, evidence for the
$B^0\to\mu^+\mu^-$ decay is obtained with a statistical significance of three
standard deviations. The branching fraction measurements are statistically
compatible with SM predictions and impose stringent constraints on several
theories beyond the SM.
-
The Asia-Europe-Pacific School of High-Energy Physics is intended to give
young physicists an introduction to the theoretical aspects of recent advances
in elementary particle physics. These proceedings contain lectures on quantum
field theory, quantum chromodynamics, flavour physics and CP-violation, physics
beyond the Standard Model, neutrino physics, particle cosmology, heavy-ion
physics, as well as a presentation of recent results from the Large Hadron
Collider (LHC), practical statistics for particle physicists and a short
introduction to the principles of particle physics instrumentation.
-
This report summarizes the proceedings of the 2014 Mainz Institute for
Theoretical Physics (MITP) scientific program on "High precision fundamental
constants at the TeV scale". The two outstanding parameters in the Standard
Model dealt with during the MITP scientific program are the strong coupling
constant $\alpha_s$ and the top-quark mass $m_t$. Lacking knowledge on the
value of those fundamental constants is often the limiting factor in the
accuracy of theoretical predictions. The current status on $\alpha_s$ and $m_t$
has been reviewed and directions for future research have been identified.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10000-ton return yoke made of
construction steel. The return yoke consists of five dodecagonal three-layered
barrel wheels and four end-cap disks at each end comprised of steel blocks up
to 620 mm thick, which serve as the absorber plates of the muon detection
system. Accurate characterization of the magnetic field everywhere in the CMS
detector is required. To measure the field in and around the steel, a system of
22 flux-loops and 82 3-D Hall sensors is installed on the return yoke blocks.
Fast discharges of the solenoid (190 s time-constant) made during the CMS
magnet surface commissioning test at the solenoid central fields of 2.64, 3.16,
3.68 and 4.01 T were used to induce voltages in the flux-loops. The voltages
are measured on-line and integrated off-line to obtain the magnetic flux in the
steel yoke close to the muon chambers at full excitations of the solenoid. The
3-D Hall sensors installed on the steel-air interfaces give supplementary
information on the components of magnetic field and permit to estimate the
remanent field in steel to be added to the magnetic flux density obtained by
the voltages integration. A TOSCA 3-D model of the CMS magnet is developed to
describe the magnetic field everywhere outside the tracking volume measured
with the field-mapping machine. The results of the measurements and
calculations are presented, compared and discussed.
-
The Compact Muon Solenoid (CMS) is a general-purpose detector designed to run
at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive featuresinclude a 4 T superconducting solenoid with 6 m diameter by
12.5 m long free bore, enclosed inside a 10000-ton return yoke made of
construction steel. Accurate characterization of the magnetic field everywhere
in the CMS detector is required. During two major tests of the CMS magnet the
magnetic flux density was measured inside the coil in a cylinder of 3.448 m
diameter and 7 m length with a specially designed field-mapping pneumatic
machine as well as in 140 discrete regions of the CMS yoke with NMR probes, 3-D
Hall sensors and flux-loops. A TOSCA 3-D model of the CMS magnet has been
developed to describe the magnetic field everywhere outside the tracking volume
measured with the field-mapping machine. A volume based representation of the
magnetic field is used to provide the CMS simulation and reconstruction
software with the magnetic field values. The value of the field at a given
point of a volume is obtained by interpolation from a regular grid of values
resulting from a TOSCA calculation or, when available, from a parameterization.
The results of the measurements and calculations are presented, compared and
discussed.
-
The measurement of the magnetic field in the tracking volume inside the
superconducting coil of the Compact Muon Solenoid (CMS) detector under
construction at CERN is done with a fieldmapper designed and produced at
Fermilab. The fieldmapper uses 10 3-D B-sensors (Hall probes) developed at
NIKHEF and calibrated at CERN to precision 0.05% for a nominal 4 T field. The
precise fieldmapper measurements are done in 33840 points inside a cylinder of
1.724 m radius and 7 m long at central fields of 2, 3, 3.5, 3.8, and 4 T. Three
components of the magnetic flux density at the CMS coil maximum excitation and
the remanent fields on the steel-air interface after discharge of the coil are
measured in check-points with 95 3-D B-sensors located near the magnetic flux
return yoke elements. Voltages induced in 22 flux-loops made of 405-turn
installed on selected segments of the yoke are sampled online during the entire
fast discharge (190 s time-constant) of the CMS coil and integrated offline to
provide a measurement of the initial magnetic flux density in steel at the
maximum field to an accuracy of a few percent. The results of the measurements
made at 4 T are reported and compared with a three-dimensional model of the CMS
magnet system calculated with TOSCA.
-
The DZERO experiment located at Fermilab has recently started RunII with an
upgraded detector. The RunII physics program requires the Data Acquisition to
readout the detector at a rate of 1 KHz. Events fragments, totaling 250 KB, are
readout from approximately 60 front end crates and sent to a particular farm
node for Level 3 Trigger processing. A scalable system, capable of complex
event routing, has been designed and implemented based on commodity components:
VMIC 7750 Single Board Computers for readout, a Cisco 6509 switch for data
flow, and close to 100 Linux-based PCs for high-level event filtering.
-
The DZERO experiment, located at the Fermi National Accelerator Laboratory,
has recently started the Run 2 physics program. The detector upgrade included a
new Data Acquisition/Level 3 Trigger system. Part of the design for the
DAQ/Trigger system was a new monitoring infrastructure. The monitoring was
designed to satisfy real-time requirements with 1-second resolution as well as
non-real-time data. It was also designed to handle a large number of displays
without putting undue load on the sources of monitoring information. The
resulting protocol is based on XML, is easily extensible, and has spawned a
large number of displays, clients, and other applications. It is also one of
the few sources of detector performance available outside the Online System's
security wall. A tool, based on this system, which provides for auto-recovery
of DAQ errors, has been designed. This talk will include a description of the
DZERO DAQ/Online monitor server, based on the ACE framework, the protocol, the
auto-recovery tool, and several of the unique displays which include an
ORACLE-based archiver and numerous GUIs.
-
The photon radiation in the initial state lowers the energy available for the
e$^+$e$^-$ collisions; this effect is particularly important at LEP2 energies
(above the mass of the Z boson). Being aligned to the beam direction, such
initial state radiation is mostly undetected. This article describes the
procedure used by the DELPHI experiment at LEP to estimate the effective
centre-of-mass energy in hadronic events collected at energies above the Z
peak. Typical resolutions ranging from 2 to 3 GeV on the effective
center-of-mass energy are achieved, depending on the event topology.
A joint measurement is presented of the branching fractions $B^0_s\to\mu^+\mu^-$ and $B^0\to\mu^+\mu^-$ in proton-proton collisions at the LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis produces the first observation of the $B^0_s\to\mu^+\mu^-$ decay, with a statistical significance exceeding six standard deviations, and the best measurement of its branching fraction so far. Furthermore, evidence for the $B^0\to\mu^+\mu^-$ decay is obtained with a statistical significance of three standard deviations. The branching fraction measurements are statistically compatible with SM predictions and impose stringent constraints on several theories beyond the SM.
This report summarizes the proceedings of the 2014 Mainz Institute for Theoretical Physics (MITP) scientific program on "High precision fundamental constants at the TeV scale". The two outstanding parameters in the Standard Model dealt with during the MITP scientific program are the strong coupling constant $\alpha_s$ and the top-quark mass $m_t$. Lacking knowledge on the value of those fundamental constants is often the limiting factor in the accuracy of theoretical predictions. The current status on $\alpha_s$ and $m_t$ has been reviewed and directions for future research have been identified.