-
We investigate the three dimensional substructure of hadronic showers in the
CALICE scintillator-steel hadronic calorimeter. The high granularity of the
detector is used to find track segments of minimum ionising particles within
hadronic showers, providing sensitivity to the spatial structure and the
details of secondary particle production in hadronic cascades. The
multiplicity, length and angular distribution of identified track segments are
compared to GEANT4 simulations with several different shower models. Track
segments also provide the possibility for in-situ calibration of highly
granular calorimeters.
-
The EUDET-project was launched to create an infrastructure for developing and
testing new and advanced detector technologies to be used at a future linear
collider. The aim was to make possible experimentation and analysis of data for
institutes, which otherwise could not be realized due to lack of resources. The
infrastructure comprised an analysis and software network, and instrumentation
infrastructures for tracking detectors as well as for calorimetry.
-
A data acquisition (DAQ) system has been developed which will read out and
control calorimeters serving as prototype systems for a future detector at an
electron-positron linear collider. This is a modular, flexible and scalable DAQ
system in which the hardware and signals are standards-based, using FPGAs and
serial links. The idea of a backplaneless system was also pursued with a
commercial development board housed in a PC and a chain of concentrator cards
between it and the detector forming the basis of the system. As well as
describing the concept and performance of the system, its merits and
disadvantages are discussed.
-
The CALICE collaboration is studying the design of high performance
electromagnetic and hadronic calorimeters for future International Linear
Collider detectors. For the hadronic calorimeter, one option is a highly
granular sampling calorimeter with steel as absorber and scintillator layers as
active material. High granularity is obtained by segmenting the scintillator
into small tiles individually read out via silicon photo-multipliers (SiPM).
A prototype has been built, consisting of thirty-eight sensitive layers,
segmented into about eight thousand channels. In 2007 the prototype was exposed
to positrons and hadrons using the CERN SPS beam, covering a wide range of beam
energies and incidence angles. The challenge of cell equalization and
calibration of such a large number of channels is best validated using
electromagnetic processes.
The response of the prototype steel-scintillator calorimeter, including
linearity and uniformity, to electrons is investigated and described.
-
A prototype silicon-tungsten electromagnetic calorimeter for an ILC detector
was tested in 2007 at the CERN SPS test beam. Data were collected with electron
and hadron beams in the energy range 8 to 80 GeV. The analysis described here
focuses on the interactions of pions in the calorimeter. One of the main
objectives of the CALICE program is to validate the Monte Carlo tools available
for the design of a full-sized detector. The interactions of pions in the Si-W
calorimeter are therefore confronted with the predictions of various physical
models implemented in the GEANT4 simulation framework.
-
An analog hadron calorimeter (AHCAL) prototype of 5.3 nuclear interaction
lengths thickness has been constructed by members of the CALICE Collaboration.
The AHCAL prototype consists of a 38-layer sandwich structure of steel plates
and highly-segmented scintillator tiles that are read out by
wavelength-shifting fibers coupled to SiPMs. The signal is amplified and shaped
with a custom-designed ASIC. A calibration/monitoring system based on LED light
was developed to monitor the SiPM gain and to measure the full SiPM response
curve in order to correct for non-linearity. Ultimately, the physics goals are
the study of hadron shower shapes and testing the concept of particle flow. The
technical goal consists of measuring the performance and reliability of 7608
SiPMs. The AHCAL was commissioned in test beams at DESY and CERN. The entire
prototype was completed in 2007 and recorded hadron showers, electron showers
and muons at different energies and incident angles in test beams at CERN and
Fermilab.
-
Future experiments will use silicon sensors in the harsh radiation
environment of the LHC (Large Hadron Collider) and high magnetic fields. The
drift direction of the charge carriers is affected by the Lorentz force due to
the high magnetic field. Also the resulting radiation damage changes the
properties of the drift.
In this paper measurements of the Lorentz angle of electrons and holes before
and after irradiation are reviewed and compared with a simple algorithm to
compute the Lorentz angle.
-
Future experiments are using silicon detectors in a high radiation
environment and in high magnetic fields. The radiation tolerance of silicon
improves by cooling it to temperatures below 180 K. At low temperatures the
mobility increases, which leads to larger deflections of the charge carriers by
the Lorentz force. A good knowledge of the Lorentz angle is needed for design
and operation of silicon detectors. We present measurements of the Lorentz
angle between 77 K and 300 K before and after irradiation with a primary beam
of 21 MeV protons.
We investigate the three dimensional substructure of hadronic showers in the CALICE scintillator-steel hadronic calorimeter. The high granularity of the detector is used to find track segments of minimum ionising particles within hadronic showers, providing sensitivity to the spatial structure and the details of secondary particle production in hadronic cascades. The multiplicity, length and angular distribution of identified track segments are compared to GEANT4 simulations with several different shower models. Track segments also provide the possibility for in-situ calibration of highly granular calorimeters.
A data acquisition (DAQ) system has been developed which will read out and control calorimeters serving as prototype systems for a future detector at an electron-positron linear collider. This is a modular, flexible and scalable DAQ system in which the hardware and signals are standards-based, using FPGAs and serial links. The idea of a backplaneless system was also pursued with a commercial development board housed in a PC and a chain of concentrator cards between it and the detector forming the basis of the system. As well as describing the concept and performance of the system, its merits and disadvantages are discussed.
The CALICE collaboration is studying the design of high performance electromagnetic and hadronic calorimeters for future International Linear Collider detectors. For the hadronic calorimeter, one option is a highly granular sampling calorimeter with steel as absorber and scintillator layers as active material. High granularity is obtained by segmenting the scintillator into small tiles individually read out via silicon photo-multipliers (SiPM). A prototype has been built, consisting of thirty-eight sensitive layers, segmented into about eight thousand channels. In 2007 the prototype was exposed to positrons and hadrons using the CERN SPS beam, covering a wide range of beam energies and incidence angles. The challenge of cell equalization and calibration of such a large number of channels is best validated using electromagnetic processes. The response of the prototype steel-scintillator calorimeter, including linearity and uniformity, to electrons is investigated and described.
A prototype silicon-tungsten electromagnetic calorimeter for an ILC detector was tested in 2007 at the CERN SPS test beam. Data were collected with electron and hadron beams in the energy range 8 to 80 GeV. The analysis described here focuses on the interactions of pions in the calorimeter. One of the main objectives of the CALICE program is to validate the Monte Carlo tools available for the design of a full-sized detector. The interactions of pions in the Si-W calorimeter are therefore confronted with the predictions of various physical models implemented in the GEANT4 simulation framework.
An analog hadron calorimeter (AHCAL) prototype of 5.3 nuclear interaction lengths thickness has been constructed by members of the CALICE Collaboration. The AHCAL prototype consists of a 38-layer sandwich structure of steel plates and highly-segmented scintillator tiles that are read out by wavelength-shifting fibers coupled to SiPMs. The signal is amplified and shaped with a custom-designed ASIC. A calibration/monitoring system based on LED light was developed to monitor the SiPM gain and to measure the full SiPM response curve in order to correct for non-linearity. Ultimately, the physics goals are the study of hadron shower shapes and testing the concept of particle flow. The technical goal consists of measuring the performance and reliability of 7608 SiPMs. The AHCAL was commissioned in test beams at DESY and CERN. The entire prototype was completed in 2007 and recorded hadron showers, electron showers and muons at different energies and incident angles in test beams at CERN and Fermilab.