-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of
construction steel. The flux return yoke consists of five dodecagonal
three-layered barrel wheels and four end-cap disks at each end comprised of
steel blocks up to 620 mm thick, which serve as the absorber plates of the muon
detection system. To measure the field in and around the steel, a system of 22
flux loops and 82 3-D Hall sensors is installed on the return yoke blocks. A
TOSCA 3-D model of the CMS magnet is developed to describe the magnetic field
everywhere outside the tracking volume that was measured with the field-mapping
machine. The voltages induced in the flux loops by the magnetic flux changing
during the CMS magnet standard ramps down are measured with six 16-bit DAQ
modules. The off-line integration of the induced voltages reconstructs the
magnetic flux density in the yoke steel blocks at the operational magnet
current of 18.164 kA. The results of the flux loop measurements during three
magnet ramps down are presented and discussed.
-
Measurements of multiplicity and transverse momentum fluctuations of charged
particles were performed in inelastic p+p interactions at 20, 31, 40, 80 and
158 GeV/c beam momentum. Results for the scaled variance of the multiplicity
distribution and for three strongly intensive measures of multiplicity and
transverse momentum fluctuations \$\Delta[P_{T},N]\$, \$\Sigma[P_{T},N]\$ and
\$\Phi_{p_T}\$ are presented. For the first time the results on fluctuations
are fully corrected for experimental biases. The results on multiplicity and
transverse momentum fluctuations significantly deviate from expectations for
the independent particle production. They also depend on charges of selected
hadrons. The string-resonance Monte Carlo models EPOS and UrQMD do not describe
the data. The scaled variance of multiplicity fluctuations is significantly
higher in inelastic p+p interactions than in central Pb+Pb collisions measured
by NA49 at the same energy per nucleon. This is in qualitative disagreement
with the predictions of the Wounded Nucleon Model. Within the statistical
framework the enhanced multiplicity fluctuations in inelastic p+p interactions
can be interpreted as due to event-by-event fluctuations of the fireball energy
and/or volume.
-
The conceptual design study of a Future Circular hadron-hadron Collider
(FCC-hh) with a center-of-mass energy of the order of 100 TeV, assumed to be
constructed in a new tunnel of 80-100 km circumference, includes the
determination of the basic requirements for its detectors. A superconducting
solenoid magnet of 12-m-diameter inner bore with the central magnetic flux
density of 6 T, in combination with two superconducting dipole magnets and two
conventional toroid magnets is proposed for an FCC-hh experimental setup. The
coil of 23.468 m length has seven 3.35-m-long modules included into one
cryostat. The steel yoke with a mass of 22.6 kt consists of two barrel layers
of 0.5 m radial thickness and a 0.7-m-thick nose disk and four 0.6-m-thick
end-cap disks each side. The outer diameter of the yoke is 17.7 m. The full
length of the magnetic system is 62.6 m. The air gaps between the end-cap disks
provide for the installation of the muon chambers up to an absolute
pseudorapidity about 2.7. The superconducting dipole magnets provide
measurement of charged particle momenta in the absolute pseudorapidity region
greater than 3. The conventional forward muon spectrometer allows muon
identification in the absolute pseudorapidity region from 2.7 to 5. The magnet
is modeled with the program TOSCA from Cobham CTS Limited. The total current in
the superconducting solenoid coil is 123 MA-turns; the stored energy is 41.8
GJ. The axial force acting on each end-cap is 450 MN. The stray field is 13.7
mT at a radius of 50 m from the coil axis, and 5.2 mT at a radius of 100 m.
Many other parameters are presented and discussed.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of
construction steel. The return yoke consists of five dodecagonal three-layered
barrel wheels and four end-cap disks at each end comprised of steel blocks up
to 620 mm thick, which serve as the absorber plates of the muon detection
system. To measure the field in and around the steel, a system of 22 flux loops
and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D
model of the CMS magnet is developed to describe the magnetic field everywhere
outside the tracking volume measured with the field-mapping machine. The
magnetic field description is compared with the measurements and discussed.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10,000-ton return yoke made of
construction steel. The return yoke consists of five dodecagonal three-layered
barrel wheels and four end-cap disks at each end comprised of steel blocks up
to 620 mm thick, which serve as the absorber plates of the muon detection
system. To measure the field in and around the steel, a system of 22 flux loops
and 82 3-D Hall sensors is installed on the return yoke blocks. A TOSCA 3-D
model of the CMS magnet is developed to describe the magnetic field everywhere
outside the tracking volume measured with the field-mapping machine. The first
attempt is made to measure the magnetic flux density in the steel blocks of the
CMS magnet yoke using the standard magnet discharge with the current ramp down
speed of 1.5 A/s.
-
Measurements of hadron production in p+C interactions at 31 GeV/c are
performed using the NA61/ SHINE spectrometer at the CERN SPS. The analysis is
based on the full set of data collected in 2009 using a graphite target with a
thickness of 4% of a nuclear interaction length. Inelastic and production cross
sections as well as spectra of $\pi^\pm$, $K^\pm$, p, $K^0_S$ and $\Lambda$ are
measured with high precision. These measurements are essential for improved
calculations of the initial neutrino fluxes in the T2K long-baseline neutrino
oscillation experiment in Japan. A comparison of the NA61/SHINE measurements
with predictions of several hadroproduction models is presented.
-
Mass and momentum exchanges in close massive binaries play an important role
in their evolution, and produce several observational signatures such as
asynchronous rotation and altered chemical compositions, that remain after the
stars detach again. We investigated these effects for the detached massive
O-star binary HD 149404 (O7.5If + ON9.7I, P = 9.81 days), which is thought to
have experienced a past episode of case A Roche-lobe overflow (RLOF). Using
phase-resolved spectroscopy, we performed the disentangling of the optical
spectra of the two stars. The reconstructed primary and secondary spectra were
then analysed with the CMFGEN model atmosphere code to determine stellar
parameters, such as the effective temperatures and surface gravities, and to
constrain the chemical composition of the components. We complemented the
optical study with the study of IUE spectra, which we compare to the synthetic
binary spectra. The properties of the stars were compared to evolutionary
models. We confirmed a strong overabundance in nitrogen ($\left[\rm
N/C\right]\sim150\left[\rm N/C\right]_{\odot}$) for the secondary and a slight
nitrogen overabundance ($\left[\rm N/C\right]\sim5\left[\rm
N/C\right]_{\odot}$) for the primary star. Comparing the two stars, we found
evidence for asynchronous rotation, with a rotational period ratio of $0.50 \pm
0.11$. The hypothesis of a past case A RLOF interaction in HD 149404 is most
plausible to explain its chemical abundances and rotational asynchronicity.
Some of the observed properties, such as the abundance pattern, are clearly a
challenge for current case A binary evolution models, however.
-
The conceptual design study of a hadron Future Circular Collider (FCC-hh)
with a center-of-mass energy of the order of 100 TeV in a new tunnel of 80-100
km circumference assumes the determination of the basic requirements for its
detectors. A superconducting solenoid magnet of 12 m diameter inner bore with
the central magnetic flux density of 6 T is proposed for a FCC-hh experimental
setup. The coil of 24.518 m long has seven 3.5 m long modules included into one
cryostat. The steel yoke with a mass of 21 kt consists of two barrel layers of
0.5 m radial thickness, and 0.7 m thick nose disk, four 0.6 m thick end-cap
disks, and three 0.8 m thick muon toroid disks each side. The outer diameter of
the yoke is 17.7 m; the length without the forward muon toroids is 33 m. The
air gaps between the end-cap disks provide the installation of the muon
chambers up to the pseudorapidity of \pm 3.5. The conventional forward muon
spectrometer provides the measuring of the muon momenta in the pseudorapidity
region from \pm 2.7 to \pm 4.6. The magnet modeled with Cobham's program TOSCA.
The total Ampere-turns in the superconducting solenoid coil are 127.25
MA-turns. The stored energy is 43.3 GJ. The axial force onto each end-cap is
480 MN. The stray field at the radius of 50 m off the coil axis is 14.1 mT and
5.4 mT at the radius of 100 m. All other parameters presented and discussed.
-
The evolution of massive stars is only partly understood. Observational
constraints can be obtained from the study of massive stars located in young
massive clusters. The ESO Public Survey VISTA Variables in the Via Lactea (VVV)
discovered several new clusters hosting massive stars. We present an analysis
of massive stars in four of these new clusters. Our aim is to provide
constraints on stellar evolution and to better understand the relation between
different types of massive stars. We use the radiative transfer code CMFGEN to
analyse K-band spectra of twelve stars with spectral types ranging from O and B
to WN and WC. We derive the stellar parameters of all targets as well as
surface abundances for a subset of them. In the Hertzsprung-Russell diagram,
the Wolf-Rayet stars are more luminous or hotter than the O stars. From the
log(C/N) - log(C/He) diagram, we show quantitatively that WN stars are more
chemically evolved than O stars, WC stars being more evolved than WN stars.
Mass loss rates among Wolf-Rayet stars are a factor of 10 larger than for O
stars, in agreement with previous findings.
-
A joint measurement is presented of the branching fractions
$B^0_s\to\mu^+\mu^-$ and $B^0\to\mu^+\mu^-$ in proton-proton collisions at the
LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at
a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis
produces the first observation of the $B^0_s\to\mu^+\mu^-$ decay, with a
statistical significance exceeding six standard deviations, and the best
measurement of its branching fraction so far. Furthermore, evidence for the
$B^0\to\mu^+\mu^-$ decay is obtained with a statistical significance of three
standard deviations. The branching fraction measurements are statistically
compatible with SM predictions and impose stringent constraints on several
theories beyond the SM.
-
Probing the structures of stellar winds is of prime importance for the
understanding of massive stars. Based on their optical spectral morphology and
variability, the stars of the Oef class have been suggested to feature
large-scale structures in their wind. High-resolution X-ray spectroscopy and
time-series of X-ray observations of presumably-single O-type stars can help us
understand the physics of their stellar winds. We have collected XMM-Newton
observations and coordinated optical spectroscopy of the O6Ief star lambda Cep
to study its X-ray and optical variability and to analyse its high-resolution
X-ray spectrum. We investigate the line profile variability of the He II 4686
and H-alpha emission lines in our time series of optical spectra, including a
search for periodicities. We further discuss the variability of the broadband
X-ray flux and analyse the high-resolution spectrum of lambda Cep using
line-by-line fits as well as a code designed to fit the full high-resolution
X-ray spectrum consistently. During our observing campaign, the He II 4686 line
varies on a timescale of ~18 hours. On the contrary, the H-alpha line profile
displays a modulation on a timescale of 4.1 days which is likely the rotation
period of the star. The X-ray flux varies on time-scales of days and could in
fact be modulated by the same 4.1 days period as H-alpha, although both
variations are shifted in phase. The high-resolution X-ray spectrum reveals
broad and skewed emission lines as expected for the X-ray emission from a
distribution of wind-embedded shocks. Most of the X-ray emission arises within
less than 2R* above the photosphere.
-
Stars over a wide range of masses and evolutionary stages are nowadays known
to emit X-rays. This X-ray emission is a unique probe of the most energetic
phenomena occurring in the circumstellar environment of these stars, and
provides precious insight on magnetic phenomena or hydrodynamic shocks. Owing
to its large collecting area, Athena+ will open up an entirely new window on
these phenomena. Indeed, Athena+ will not only allow us to study many more
objects with an unprecedented spectral resolution, but will also pioneer the
study of the dynamics of these objects via time-resolved high-resolution
spectroscopy. In this way, Athena+ will be a unique tool to study accretion
processes in TTauri stars, flaring activity in young stars, dynamos in
ultra-cool dwarfs, small and large-scale structures in the winds of single
massive stars, wind interactions in massive binary systems, hot bubbles in
planetary nebula... All these studies will lead to a deeper understanding of
yet poorly understood processes which have profound impact in star and
planetary system formation as well as in feedback processes on Galactic scale.
-
Context. Zeta Pup is the X-ray brightest O-type star of the sky. This object
was regularly observed with the RGS instrument aboard XMM-Newton for
calibration purposes, leading to an unprecedented set of high-quality spectra.
Aims. We have previously reduced and extracted this data set and combined it
into the most detailed high-resolution X-ray spectrum of any early-type star so
far. Here we present the analysis of this spectrum accounting for the presence
of structures in the stellar wind. Methods. For this purpose, we use our new
modeling tool that allows fitting the entire spectrum with a multi-temperature
plasma. We illustrate the impact of a proper treatment of the radial dependence
of the X-ray opacity of the cool wind on the best-fit radial distribution of
the temperature of the X-ray plasma. Results. The best fit of the RGS spectrum
of Zeta Pup is obtained assuming no porosity. Four plasma components at
temperatures between 0.10 and 0.69 keV are needed to adequately represent the
observed spectrum. Whilst the hardest emission is concentrated between ~3 and 4
R*, the softer emission starts already at 1.5 R* and extends to the outer
regions of the wind. Conclusions. The inferred radial distribution of the
plasma temperatures agrees rather well with theoretical expectations. The mass-
loss rate and CNO abundances corresponding to our best-fit model also agree
quite well with the results of recent studies of Zeta Pup in the UV and optical
domain.
-
The present note relies on the recently published conceptual design report of
the LHeC and extends the first contribution to the European strategy debate in
emphasising the role of the LHeC to complement and complete the high luminosity
LHC programme. The brief discussion therefore focuses on the importance of high
precision PDF and $\alpha_s$ determinations for the physics beyond the Standard
Model (GUTs, SUSY, Higgs). Emphasis is also given to the importance of high
parton density phenomena in nuclei and their relevance to the heavy ion physics
programme at the LHC.
-
This document provides a brief overview of the recently published report on
the design of the Large Hadron Electron Collider (LHeC), which comprises its
physics programme, accelerator physics, technology and main detector concepts.
The LHeC exploits and develops challenging, though principally existing,
accelerator and detector technologies. This summary is complemented by brief
illustrations of some of the highlights of the physics programme, which relies
on a vastly extended kinematic range, luminosity and unprecedented precision in
deep inelastic scattering. Illustrations are provided regarding high precision
QCD, new physics (Higgs, SUSY) and electron-ion physics. The LHeC is designed
to run synchronously with the LHC in the twenties and to achieve an integrated
luminosity of O(100) fb$^{-1}$. It will become the cleanest high resolution
microscope of mankind and will substantially extend as well as complement the
investigation of the physics of the TeV energy scale, which has been enabled by
the LHC.
-
The Compact Muon Solenoid (CMS) is a general purpose detector, designed to
run at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive features include a 4 T superconducting solenoid with 6-m-diameter
by 12.5-m-length free bore, enclosed inside a 10000-ton return yoke made of
construction steel. The return yoke consists of five dodecagonal three-layered
barrel wheels and four end-cap disks at each end comprised of steel blocks up
to 620 mm thick, which serve as the absorber plates of the muon detection
system. Accurate characterization of the magnetic field everywhere in the CMS
detector is required. To measure the field in and around the steel, a system of
22 flux-loops and 82 3-D Hall sensors is installed on the return yoke blocks.
Fast discharges of the solenoid (190 s time-constant) made during the CMS
magnet surface commissioning test at the solenoid central fields of 2.64, 3.16,
3.68 and 4.01 T were used to induce voltages in the flux-loops. The voltages
are measured on-line and integrated off-line to obtain the magnetic flux in the
steel yoke close to the muon chambers at full excitations of the solenoid. The
3-D Hall sensors installed on the steel-air interfaces give supplementary
information on the components of magnetic field and permit to estimate the
remanent field in steel to be added to the magnetic flux density obtained by
the voltages integration. A TOSCA 3-D model of the CMS magnet is developed to
describe the magnetic field everywhere outside the tracking volume measured
with the field-mapping machine. The results of the measurements and
calculations are presented, compared and discussed.
-
Context: The ESO Public Survey "VISTA Variables in the V\'ia L\'actea" (VVV)
provides deep multi-epoch infrared observations for an unprecedented 562 sq.
degrees of the Galactic bulge, and adjacent regions of the disk. In this survey
nearly 150 new open clusters and cluster candidates have been discovered. Aims:
This is the second in a series of papers about young, massive open clusters
observed using the VVV survey. We present the first study of six recently
discovered clusters. These clusters contain at least one newly discovered
Wolf-Rayet (WR) star. Methods: Following the methodology presented in the first
paper of the series, wide-field, deep JHKs VVV observations, combined with new
infrared spectroscopy, are employed to constrain fundamental parameters for a
subset of clusters. Results: We affirm that the six studied stellar groups are
real young (2-7 Myr) and massive (between 0.8 and 2.2 10^3 Msol) clusters. They
are highly obscured (Av ~ 5-24 mag) and compact (1-2 pc). In addition to WR
stars, two of the six clusters also contain at least one red supergiant star.
We claim the discovery of 8 new WR stars, and 3 stars showing WR-like emission
lines which could be classified WR or OIf. Preliminary analysis provides
initial masses of ~30-50 Msol for the WR stars. Finally,we discuss the spiral
structure of the Galaxy using as tracers the six new clusters together with the
previously studied VVV clusters.
-
The physics programme and the design are described of a new collider for
particle and nuclear physics, the Large Hadron Electron Collider (LHeC), in
which a newly built electron beam of 60 GeV, up to possibly 140 GeV, energy
collides with the intense hadron beams of the LHC. Compared to HERA, the
kinematic range covered is extended by a factor of twenty in the negative
four-momentum squared, $Q^2$, and in the inverse Bjorken $x$, while with the
design luminosity of $10^{33}$ cm$^{-2}$s$^{-1}$ the LHeC is projected to
exceed the integrated HERA luminosity by two orders of magnitude. The physics
programme is devoted to an exploration of the energy frontier, complementing
the LHC and its discovery potential for physics beyond the Standard Model with
high precision deep inelastic scattering measurements. These are designed to
investigate a variety of fundamental questions in strong and electroweak
interactions. The physics programme also includes electron-deuteron and
electron-ion scattering in a $(Q^2, 1/x)$ range extended by four orders of
magnitude as compared to previous lepton-nucleus DIS experiments for novel
investigations of neutron's and nuclear structure, the initial conditions of
Quark-Gluon Plasma formation and further quantum chromodynamic phenomena. The
LHeC may be realised either as a ring-ring or as a linac-ring collider. Optics
and beam dynamics studies are presented for both versions, along with technical
design considerations on the interaction region, magnets and further
components, together with a design study for a high acceptance detector. Civil
engineering and installation studies are presented for the accelerator and the
detector. The LHeC can be built within a decade and thus be operated while the
LHC runs in its high-luminosity phase. It thus represents a major opportunity
for progress in particle physics exploiting the investment made in the LHC.
-
High-resolution X-ray spectra of O-type stars revealed less wind absorption
than expected from smooth winds with conventional mass-loss rates. Various
solutions have been proposed, including porous winds, optically thick clumps or
an overall reduction of the mass-loss rates. The latter has a strong impact on
the evolution of the star. Our final goal is to analyse high resolution X-ray
spectra of O-type stars with a multi temperature plasma model in order to
determine crucial wind parameters such as the mass loss rate, the CNO
abundances and the X-ray temperature plasma distribution in the wind. In this
context we are developing a modelling tool to calculate synthetic X-ray
spectra. We present, here, the main ingredients and physics necessary for a
such work. Our code uses the AtomDB emissivities to compute the intrinsic
emissivity of the hot plasma as well as the CMFGEN model atmosphere code to
evaluate the opacity of the cool wind. Following the comparison between two
formalisms of stellar wind fragmentation, we introduce, for the first time in
X-rays, the effects of a tenuous inter-clump medium. We then explore the
quantitative impact of different model parameters on the X-ray spectra such as
the position in the wind of the X-ray emitting plasma. For the first time, we
show that the two formalisms of stellar wind fragmentation yield different
results, although the differences for individual lines are small and can
probably not be tested with the current generation of X-ray telescopes. As an
illustration of our method, we compare various synthetic line profiles to the
observed O VIII {\lambda} 18.97{\AA} line in the spectrum of {\zeta} Puppis. We
illustrate how different combinations of parameters can actually lead to the
same morphology of a single line, underlining the need to analyse the whole
spectrum in a consistent way when attempting to constrain the parameters of the
wind.
-
The Compact Muon Solenoid (CMS) is a general-purpose detector designed to run
at the highest luminosity at the CERN Large Hadron Collider (LHC). Its
distinctive featuresinclude a 4 T superconducting solenoid with 6 m diameter by
12.5 m long free bore, enclosed inside a 10000-ton return yoke made of
construction steel. Accurate characterization of the magnetic field everywhere
in the CMS detector is required. During two major tests of the CMS magnet the
magnetic flux density was measured inside the coil in a cylinder of 3.448 m
diameter and 7 m length with a specially designed field-mapping pneumatic
machine as well as in 140 discrete regions of the CMS yoke with NMR probes, 3-D
Hall sensors and flux-loops. A TOSCA 3-D model of the CMS magnet has been
developed to describe the magnetic field everywhere outside the tracking volume
measured with the field-mapping machine. A volume based representation of the
magnetic field is used to provide the CMS simulation and reconstruction
software with the magnetic field values. The value of the field at a given
point of a volume is obtained by interpolation from a regular grid of values
resulting from a TOSCA calculation or, when available, from a parameterization.
The results of the measurements and calculations are presented, compared and
discussed.
-
The measurement of the magnetic field in the tracking volume inside the
superconducting coil of the Compact Muon Solenoid (CMS) detector under
construction at CERN is done with a fieldmapper designed and produced at
Fermilab. The fieldmapper uses 10 3-D B-sensors (Hall probes) developed at
NIKHEF and calibrated at CERN to precision 0.05% for a nominal 4 T field. The
precise fieldmapper measurements are done in 33840 points inside a cylinder of
1.724 m radius and 7 m long at central fields of 2, 3, 3.5, 3.8, and 4 T. Three
components of the magnetic flux density at the CMS coil maximum excitation and
the remanent fields on the steel-air interface after discharge of the coil are
measured in check-points with 95 3-D B-sensors located near the magnetic flux
return yoke elements. Voltages induced in 22 flux-loops made of 405-turn
installed on selected segments of the yoke are sampled online during the entire
fast discharge (190 s time-constant) of the CMS coil and integrated offline to
provide a measurement of the initial magnetic flux density in steel at the
maximum field to an accuracy of a few percent. The results of the measurements
made at 4 T are reported and compared with a three-dimensional model of the CMS
magnet system calculated with TOSCA.
-
Flux loops have been installed on selected segments of the magnetic flux
return yoke of the 4 T superconducting coil of the Compact Muon Solenoid (CMS)
detector under construction at CERN. Voltages induced in the loops during
discharge of the solenoid will be sampled online during the entire discharge
and integrated offline to provide a measurement of the initial magnetic flux
density in steel at the maximum field to an accuracy of a few percent. Although
the discharge of the solenoid is rather slow (190 s time constant), the
influence of eddy currents induced in the yoke elements should be estimated.
The calculation of eddy currents is performed with Vector Fields' program
ELEKTRA. The results of the calculations are reported.
-
Compact muon solenoid (CMS) is a general-purpose detector designed to run at
the highest luminosity at the CERN large hadron collider (LHC). Its distinctive
features include a 4 T superconducting solenoid with 6 m diameter by 12.5 m
long free bore, enclosed inside a 10000-ton return yoke made of construction
steel. Accurate characterization of the magnetic field everywhere in
theCMSdetector, including the large ferromagnetic parts of the yoke, is
required. To measure the field in and around ferromagnetic parts, a set of
flux-loops and Hall probe sensors will be installed on several of the steel
pieces. Fast discharges of the solenoid during system commissioning tests will
be used to induce voltages in the flux-loops that can be integrated to measure
the flux in the steel at full excitation of the solenoid. The Hall sensors will
give supplementary information on the axial magnetic field and permit
estimation of the remanent field in the steel after the fast discharge. An
experimental R&D program has been undertaken, using a test flux-loop, two Hall
sensors, and sample disks made from the same construction steel used for the
CMS magnet yoke. A sample disc, assembled with the test flux-loop and the Hall
sensors, was inserted between the pole tips of a dipole electromagnet equipped
with a computer-controlled power supply to measure the excitation of the steel
from full saturation to zero field. The results of the measurements are
presented and discussed.
-
The CMS magnetic system consists of a super-conducting solenoid coil, 12.5 m
long and 6 m free bore diameter, and of an iron flux-return yoke, which
includes the central barrel, two end-caps and the ferromagnetic parts of the
hadronic forward calorimeter. The magnetic flux density in the center of the
solenoid is 4 T. To carry out the magnetic analysis of the CMS magnetic system,
several 3D models were developed to perform magnetic field and force
calculations using the Vector Fields code TOSCA. The analysis includes a study
of the general field behavior, the calculation of the forces on the coil
generated by small axial, radial displacements and angular tilts, the
calculation of the forces on the ferromagnetic parts, the calculation of the
fringe field outside the magnetic system, and a study of the field level in the
chimneys for the current leads and the cryogenic lines. A procedure to
reconstruct the field inside a cylindrical volume starting from the values of
the magnetic flux density on the cylinder surface is considered. Special
TOSCA-GEANT interface tools have being developed to input the calculated
magnetic field into the detector simulation package.