-
PFS (Prime Focus Spectrograph), a next generation facility instrument on the
8.2-meter Subaru Telescope, is a very wide-field, massively multiplexed,
optical and near-infrared spectrograph. Exploiting the Subaru prime focus, 2394
reconfigurable fibers will be distributed over the 1.3 deg field of view. The
spectrograph has been designed with 3 arms of blue, red, and near-infrared
cameras to simultaneously observe spectra from 380nm to 1260nm in one exposure
at a resolution of ~1.6-2.7A. An international collaboration is developing this
instrument under the initiative of Kavli IPMU. The project is now going into
the construction phase aiming at undertaking system integration in 2017-2018
and subsequently carrying out engineering operations in 2018-2019. This article
gives an overview of the instrument, current project status and future paths
forward.
-
The Prime Focus Spectrograph (PFS) is a new optical/near-infrared multi-fiber
spectrograph design for the prime focus of the 8.2m Subaru telescope. PFS will
cover 1.3 degree diameter field with 2394 fibers to complement the imaging
capability of Hyper SuprimeCam (HSC). The prime focus unit of PFS called Prime
Focus Instrument (PFI) provides the interface with the top structure of Subaru
telescope and also accommodates the optical bench in which Cobra fiber
positioners are located. In addition, the acquisition and guiding cameras
(AGCs), the optical fiber positioner system, the cable wrapper, the fiducial
fibers, illuminator, and viewer, the field element, and the telemetry system
are located inside the PFI. The mechanical structure of the PFI was designed
with special care such that its deflections sufficiently match those of the
HSC's Wide Field Corrector (WFC) so the fibers will stay on targets over the
course of the observations within the required accuracy. In this report, the
latest status of PFI development will be given including the performance of PFI
components, the setup and performance of the integration and testing equipment.
-
The Prime Focus Spectrograph (PFS) is an optical/near-infrared multifiber
spectrograph with 2394 science fibers distributed across a 1.3-deg diameter
field of view at the Subaru 8.2-m telescope. The wide wavelength coverage from
0.38 {\mu}m to 1.26 {\mu}m, with a resolving power of 3000, simultaneously
strengthens its ability to target three main survey programs: cosmology,
galactic archaeology and galaxy/AGN evolution. A medium resolution mode with a
resolving power of 5000 for 0.71 {\mu}m to 0.89 {\mu}m will also be available
by simply exchanging dispersers. We highlight some of the technological aspects
of the design. To transform the telescope focal ratio, a broad-band coated
microlens is glued to each fiber tip. A higher transmission fiber is selected
for the longest part of the cable system, optimizing overall throughput; a
fiber with low focal ratio degradation is selected for the fiber-positioner and
fiber-slit components, minimizing the effects of fiber movements and fiber
bending. Fiber positioning will be performed by a positioner consisting of two
stages of piezo-electric rotary motors. The positions of these motors are
measured by taking an image of artificially back-illuminated fibers with the
metrology camera located in the Cassegrain container; the fibers are placed in
the proper location by iteratively measuring and then adjusting the positions
of the motors. Target light reaches one of the four identical fast-Schmidt
spectrograph modules, each with three arms. The PFS project has passed several
project-wide design reviews and is now in the construction phase.
-
The Prime Focus Spectrograph (PFS) is an optical/near-infrared multi-fiber
spectrograph with 2394 science fibers, which are distributed in 1.3 degree
diameter field of view at Subaru 8.2-meter telescope. The simultaneous wide
wavelength coverage from 0.38 um to 1.26 um, with the resolving power of 3000,
strengthens its ability to target three main survey programs: cosmology,
Galactic archaeology, and galaxy/AGN evolution. A medium resolution mode with
resolving power of 5000 for 0.71 um to 0.89 um also will be available by simply
exchanging dispersers. PFS takes the role for the spectroscopic part of the
Subaru Measurement of Images and Redshifts project, while Hyper Suprime-Cam
works on the imaging part. To transform the telescope plus WFC focal ratio, a
3-mm thick broad-band coated glass-molded microlens is glued to each fiber tip.
A higher transmission fiber is selected for the longest part of cable system,
while one with a better FRD performance is selected for the fiber-positioner
and fiber-slit components, given the more frequent fiber movements and tightly
curved structure. Each Fiber positioner consists of two stages of
piezo-electric rotary motors. Its engineering model has been produced and
tested. Fiber positioning will be performed iteratively by taking an image of
artificially back-illuminated fibers with the Metrology camera located in the
Cassegrain container. The camera is carefully designed so that fiber position
measurements are unaffected by small amounts of high special-frequency
inaccuracies in WFC lens surface shapes. Target light carried through the fiber
system reaches one of four identical fast-Schmidt spectrograph modules, each
with three arms. Prototype VPH gratings have been optically tested. CCD
production is complete, with standard fully-depleted CCDs for red arms and
more-challenging thinner fully-depleted CCDs with blue-optimized coating for
blue arms.
-
FOCCoS, Fiber Optical Cable and Connector System, has the main function of
capturing the direct light from the focal plane of Subaru Telescope using
optical fibers, each one with a microlens in its tip, and conducting this light
through a route containing connectors to a set of four spectrographs. The
optical fiber cable is divided in 3 different segments called Cable A, Cable B
and Cable C. Multi-fibers connectors assure precise connection among all
optical fibers of the segments, providing flexibility for instrument changes.
To assure strong and accurate connection, these sets are arranged inside two
types of assemblies: the Tower Connector, for connection between Cable C and
Cable B; and the Gang Connector, for connection between Cable B and Cable A.
Throughput tests were made to evaluate the efficiency of the connections. A
lifetime test connection is in progress. Cable C is installed inside the PFI,
Prime Focus Instrument, where each fiber tip with a microlens is bonded to the
end of the shaft of a 2-stage piezo-electric rotatory motor positioner; this
assembly allows each fiber to be placed anywhere within its patrol region,
which is 9.5mm diameter.. Each positioner uses a fiber arm to support the
ferrule, the microlens, and the optical fiber. 2400 of these assemblies are
arranged on a motor bench plate in a hexagonal-closed-packed disposition.
-
The Fiber Optical Cable and Connector System, FOCCoS, subsystem of the Prime
Focus Spectrograph, PFS, for Subaru telescope, is responsible to feed four
spectrographs with a set of optical fibers cables. The light injection for each
spectrograph is assured by a convex curved slit with a linear array of 616
optical fibers. In this paper we present a design of a slit that ensures the
right direction of the fibers by using masks of micro holes. This kind of mask
is made by a technique called electroforming, which is able to produce a nickel
plate with holes in a linear sequence. The precision error is around 1micron in
the diameter and 1 micron in the positions of the holes. This nickel plate may
be produced with a thickness between 50 and 200 microns, so it may be very
flexible. This flexibility allows the mask to be bent into the shape necessary
for a curved slit. The concept requires two masks, which we call Front Mask,
and Rear Mask, separated by a gap that defines the thickness of the slit. The
pitch and the diameter of the holes define the linear geometry of the slit; the
curvature of each mask defines the angular geometry of the slit. Obviously,
this assembly must be mounted inside a structure rigid and strong enough to be
supported inside the spectrograph. This structure must have a CTE optimized to
avoid displacement of the fibers or increased FRD of the fibers when the device
is submitted to temperatures around 3 degrees Celsius, the temperature of
operation of the spectrograph. We have produced two models. Both are mounted
inside a very compact Invar case, and both have their front surfaces covered by
a dark composite, to reduce stray light. Furthermore, we have conducted
experiments with two different internal structures to minimize effects caused
by temperature gradients.
-
The Fiber Optical Cable and Connector System (FOCCoS), provides optical
connection between 2400 positioners and a set of spectrographs through optical
fibers cables as part of PFS instrument for Subaru telescope. The optical fiber
cable will be segmented in 3 parts along the route, cable A, cable B and cable
C, connected by a set of multi-fiber connectors. The company USCONEC produces
the multi-fiber connector under study. The USCONEC 32F model can connect 32
optical fibers in a 4 x 8 matrix arrangement. The ferrules are made of a
durable composite, Polyphenylene Sulfide (PPS) based thermoplastic. The
connections are held in place by a push-on/pull-off latch, and the connector
can also be distinguished by a pair of metal guide pins that protrude from the
front of the connector. Two fibers per connector will be used for monitoring
the connection procedure. It was found to be easy to polish and it is small
enough to be mounted in groups. Highly multiplexed instruments like PFS require
a fiber connector system that can deliver excellent optical performance and
reliability. PFS requires two different types of structures to organize the
connectors. The Tower Connector system, with 80 multi-fiber connectors, will be
a group of connectors for connecting cable B (Telescope Structure) with cable C
(Positioners Plate). The Gang Connector system is a group of 8 gang connectors,
each one with 12 multi-fibers connectors, for connecting cable B (Telescope
Structure) with cable A (Spectrograph). The bench tests with these connector
systems and the chosen fibers should measure the throughput of light and the
stability after many connections and disconnections. In this paper we describe
tests and procedures to evaluate the throughput and FRD increment. The lifetime
of the ferrules is also in evaluation.
-
The Fiber Optical Cable and Connector System, FOCCoS, for the Prime Focus
Spectrograph, PFS, is responsible for transporting light from the Subaru
Telescope focal plane to a set of four spectrographs. Each spectrograph will be
fed by a convex curved slit with 616 optical fibers organized in a linear
arrangement. The slit frontal surface is covered with a special dark composite,
made with refractory oxide, which is able to sustain its properties with
minimum quantities of abrasives during the polishing process; this stability is
obtained This stability is obtained by the detachment of the refractory oxide
nanoparticles, which then gently reinforce gently the polishing process and
increase its the efficiency. The surface roughness measured in several samples
after high performance polishing was about 0.01 microns. Furthermore, the time
for obtaining a polished surface with this quality is about 10 times less than
the time required for polishing a brass, glass or ceramic surface of the same
size. In this paper, we describe the procedure developed for high quality
polishing of this type of slit. The cylindrical polishing described here, uses
cylindrical concave metal bases on which glass paper is based. The polishing
process consists to use grid sequences of 30 microns, 12 microns, 9 microns, 5
microns, 3 microns, 1 micron and, finally, a colloidal silica on a chemical
cloth. To obtain the maximum throughput, the surface of the fibers should be
polished in such a way that they are optically flat and free from scratches.
The optical fibers are inspected with a microscope at all stages of the
polishing process to ensure high quality. The efficiency of the process may be
improved by using a cylindrical concave composite base as a substrate suitable
for diamond liquid solutions. Despite this process being completely by hand,
the final result shows a very high quality.