• ### Field-dependent surface resistance of a superconducting RF cavity caused by surface impurity(1507.08704)

Aug. 17, 2015 physics.acc-ph
Q-slope issue, which is caused by the field dependent surface resistance, puzzled people for a long time in SRF fields. In this paper, we related the Q-slope with surface treatments; and proposed a surface-impurity model to explain the field-dependent of surface resistance of SRF cavities. Eighteen cavity-test results have been analyzed to examine the model. These cavities were treated by different recipes: Nitrogen-doping; BCP and HF-rinsing; EP with 120{\deg}C baking; and EP without 120{\deg}C baking. The performance of these cavities, which is normally represented by cavity quality factor versus accelerating gradient or surface magnetic field curves (Q0 vs. Eacc or Q0 vs. B), has included all types of Q-slope, such as Low-field Q-slope, Medium-field Q-slope, and Anti-Q-slope. The data fittings are quite successful; the fitting results will be shown. The model can be used to evaluate the effectiveness of the surface treatments. At last, the paper discussed the way to build a high-Q high-gradient SRF cavity.
• ### A temperature-mapping system for multi-cell SRF accelerating cavities(1508.01827)

Aug. 7, 2015 physics.acc-ph
A Temperature mapping (T-map) system for Superconducting Radio Frequency (SRF) cavities consists of a thermometer array positioned precisely on an exterior cavity wall, capable of detecting small increases in temperature; therefore it is a powerful tool for research on the quality factor (Q0) of SRF cavities. A new multi-cell T-mapping system is has been developed at Cornell University. The system has nearly two thousand thermometers to cover 7-cell SRF cavities for Cornell ERL project. A new multiplexing scheme was adopted to reduce number of wires. A 1mK resolution of the temperature increase Delta T is achieved. A 9-cell cavity of TESLA geometry was tested with the T-map system. By converting Delta T to power loss and quality factor, it has been found that for this cavity, most surface losses were generated by the first cell when the accelerating gradient is increased above 15MV/m. The comparison of Q-value between with and without hotspots shows the heating on cavity wall degraded cavity Q0 about 1.65 times. The power loss on the hotspots is about 40% of the total power. Effective and intuitive ways of displaying surface properties of the cavity interior, e.g. the residual resistivity, will be shown.
• ### A Storage Ring Experiment to Detect a Proton Electric Dipole Moment(1502.04317)

Feb. 15, 2015 hep-ex, physics.acc-ph
A new experiment is described to detect a permanent electric dipole moment of the proton with a sensitivity of $10^{-29}e\cdot$cm by using polarized "magic" momentum $0.7$~GeV/c protons in an all-electric storage ring. Systematic errors relevant to the experiment are discussed and techniques to address them are presented. The measurement is sensitive to new physics beyond the Standard Model at the scale of 3000~TeV.
• ### Extracting superconducting parameters from surface resistivity by using inside temperatures of SRF cavities(1405.4226)

May 16, 2014 physics.acc-ph
The surface resistance of an RF superconductor depends on the surface temperature, the residual resistance and various superconductor parameters, e.g. the energy gap, and the electron mean free path. These parameters can be determined by measuring the quality factor Q0 of a SRF cavity in helium-baths of different temperatures. The surface resistance can be computed from Q0 for any cavity geometry, but it is not trivial to determine the temperature of the surface when only the temperature of the helium bath is known. Traditionally, it was approximated that the surface temperature on the inner surface of the cavity was the same as the temperature of the helium bath. This is a good approximation at small RF-fields on the surface, but to determine the field dependence of Rs, one cannot be restricted to small field losses. Here we show the following: (1) How computer simulations can be used to determine the inside temperature Tin so that Rs(Tin) can then be used to extract the superconducting parameters. The computer code combines the well-known programs, the HEAT code and the SRIMP code. (2) How large an error is created when assuming the surface temperature is same as the temperature of the helium bath? It turns out that this error is at least 10% at high RF-fields in typical cases.
• ### Planning the Future of U.S. Particle Physics (Snowmass 2013): Chapter 6: Accelerator Capabilities(1401.6114)

Jan. 23, 2014 hep-ph, hep-ex, physics.acc-ph
These reports present the results of the 2013 Community Summer Study of the APS Division of Particles and Fields ("Snowmass 2013") on the future program of particle physics in the U.S. Chapter 6, on Accelerator Capabilities, discusses the future progress of accelerator technology, including issues for high-energy hadron and lepton colliders, high-intensity beams, electron-ion colliders, and necessary R&D for future accelerator technologies.