• If we assume line-of-sight propagation and perfect channel state information at the base station -- consistent with slow moving terminals -- then a direct performance comparison between single-cell Massive MIMO at PCS and mmWave frequency bands is straightforward and highly illuminating. Line-of-sight propagation is considered favorable for mmWave because of minimal attenuation, and its facilitation of hybrid beamforming to reduce the required number of active transceivers. We quantify the number of mmWave (60 GHz) service antennas that are needed to duplicate the performance of a specified number of PCS (1.9 GHz) service antennas. As a baseline we consider a modest PCS deployment of 128 antennas serving 18 terminals. We find that, to achieve the same per-terminal max-min 95%-likely downlink throughput, 10000 mmWave antennas are needed. To match the total antenna area of the PCS array would require 128000 half-wavelength mmWave antennas, but a much reduced number is adequate because the large number of antennas also confers greater channel orthogonality. The principal alleged benefit of mmWave technology--vast amounts of inexpensive spectrum--is at least partially offset by the complexity of possibly unwieldy amounts of hardware.
  • This paper studies the security aspect of a recently introduced network ("cell-free massive MIMO") under a pilot spoofing attack. Firstly, a simple method to recognize the presence of this type of an active eavesdropping attack to a particular user is shown. In order to deal with this attack, we consider the problem of maximizing the achievable data rate of the attacked user or its achievable secrecy rate. The corresponding problems of minimizing the consumption power subject to security constraints are also considered in parallel. Path-following algorithms are developed to solve the posed optimization problems under different power allocation to access points (APs). Under equip-power allocation to APs, these optimization problems admit closed-form solutions. Numerical results show their efficiencies.
  • Cell-free massive multiple-input multiple-output (MIMO) is a potential key technology for fifth generation wireless communication networks. A mixed quality-of-service (QoS) problem is investigated in the uplink of a cell-free massive MIMO system where the minimum rate of non-real time users is maximized with per user power constraints whilst the rate of the real-time users (RTUs) meet their target rates. First an approximated uplink user rate is derived based on available channel statistics. Next, the original mixed QoS problem is formulated in terms of receiver filter coefficients and user power allocations which can iteratively be solved through two sub-problems, namely, receiver filter coefficient design and power allocation, which are dealt with using a generalized eigenvalue problem and geometric programming, respectively. Numerical results show that with the proposed scheme, while the rates of RTUs meet the QoS constraints, the $90\%$-likely throughput improves significantly, compared to a simple benchmark scheme.
  • The concept of delivering widespread wireless communication services by splitting a coverage area into many cells dates back to the 1940s and the first practical cellular networks were trialled in the 1970s. Since then, we have witnessed an incredible wireless revolution, where cellular connectivity has gone from being a luxury product to a commodity and where the main application has changed from voice calls to data transfer. From 1G to 4G, the massive traffic growth has been managed by a combination of wider bandwidths, refined radio interfaces, and smaller cells [1]. Due its cost-efficiency, the latter has contributed the most; cell towers used to be 10 km apart and are now only 100 m apart in urban areas. While rigid frequency planning was originally used to alleviate inter-cell interference, the interference is becoming a major bottleneck as we densify the networks [2], because each cell is then hit by non-negligible interference from many neighboring cells. One way to deal with inter-cell interference is to manage it spatially by Massive MIMO (multiple-input multiple-output) methods [3], which is a key 5G technology. However, looking further ahead, we need a more radical approach; we need to challenge the cellular paradigm and realize that inter-cell interference is not a fundamental phenomenon but the result of the cell boundaries that we have purposely created in the data transmission.
  • In this paper, we consider the max-min signal-to-interference plus noise ratio (SINR) problem for the uplink transmission of a cell-free Massive multiple-input multiple-output (MIMO) system. Assuming that the central processing unit (CPU) and the users exploit only the knowledge of the channel statistics, we first derive a closed-form expression for uplink rate. In particular, we enhance (or maximize) user fairness by solving the max-min optimization problem for user rate, by power allocation and choice of receiver coefficients, where the minimum uplink rate of the users is maximized with available transmit power at the particular user. Based on the derived closed-form expression for the uplink rate, we formulate the original user max-min problem to design the optimal receiver coefficients and user power allocations. However, this max-min SINR problem is not jointly convex in terms of design variables and therefore we decompose this original problem into two sub-problems, namely, receiver coefficient design and user power allocation. By iteratively solving these sub-problems, we develop an iterative algorithm to obtain the optimal receiver coefficient and user power allocations. In particular, the receiver coefficients design for a fixed user power allocation is formulated as generalized eigenvalue problem whereas a geometric programming (GP) approach is utilized to solve the power allocation problem for a given set of receiver coefficients. Numerical results confirm a three-fold increase in system rate over existing schemes in the literature.
  • We consider a cell-free Massive multiple-input multiple-output (MIMO) system and investigate the system performance for the case when the quantized version of the estimated channel and the quantized received signal are available at the central processing unit (CPU), and the case when only the quantized version of the combined signal with maximum ratio combining (MRC) detector is available at the CPU. Next, we study the max-min optimization problem, where the minimum user uplink rate is maximized with backhaul capacity constraints. To deal with the max-min non-convex problem, we propose to decompose the original problem into two sub-problems. Based on these sub-problems, we develop an iterative scheme which solves the original max-min user uplink rate. Moreover, we present a user assignment algorithm to further improve the performance of cell-free Massive MIMO with limited backhaul links.
  • This paper considers a decode-and-forward (DF) multi-way massive multiple-input multiple-output (MIMO) relay system where many users exchange their data with the aid of a relay station equipped with a massive antenna array. We propose a new transmission protocol which leverages successive cancelation decoding and zero-forcing (ZF) at the users. By using properties of massive MIMO, a tight analytical approximation of the spectral efficiency is derived. We show that our proposed scheme uses only half of the time-slots required in the conventional scheme (in which the number of time-slots is equal to the number of users [1]), to exchange data across different users. As a result, the sum spectral efficiency of our proposed scheme is nearly double the one of the conventional scheme, thereby boosting the performance of multi-way massive MIMO to unprecedented levels.
  • We consider the cell-free massive multiple-input multiple-output (MIMO) downlink, where a very large number of distributed multiple-antenna access points (APs) serve many single-antenna users in the same time-frequency resource. A simple (distributed) conjugate beamforming scheme is applied at each AP via the use of local channel state information (CSI). This CSI is acquired through time-division duplex operation and the reception of uplink training signals transmitted by the users. We derive a closed-form expression for the spectral efficiency taking into account the effects of channel estimation errors and power control. This closed-form result enables us to analyze the effects of backhaul power consumption, the number of APs, and the number of antennas per AP on the total energy efficiency, as well as, to design an optimal power allocation algorithm. The optimal power allocation algorithm aims at maximizing the total energy efficiency, subject to a per-user spectral efficiency constraint and a per-AP power constraint. Compared with the case of without power control, our proposed power allocation scheme can double the total energy efficiency. Furthermore, we propose AP selections schemes, in which each user chooses a subset of APs, to reduce the power consumption caused by the backhaul links. With our proposed AP selection schemes, the total energy efficiency increases significantly, especially for large numbers of APs. Moreover, under a requirement of good quality-of-service for all users, cell-free massive MIMO outperforms the colocated counterpart in terms of energy efficiency.
  • A Cell-Free Massive MIMO (multiple-input multiple-output) system comprises a very large number of distributed access points (APs)which simultaneously serve a much smaller number of users over the same time/frequency resources based on directly measured channel characteristics. The APs and users have only one antenna each. The APs acquire channel state information through time-division duplex operation and the reception of uplink pilot signals transmitted by the users. The APs perform multiplexing/de-multiplexing through conjugate beamforming on the downlink and matched filtering on the uplink. Closed-form expressions for individual user uplink and downlink throughputs lead to max-min power control algorithms. Max-min power control ensures uniformly good service throughout the area of coverage. A pilot assignment algorithm helps to mitigate the effects of pilot contamination, but power control is far more important in that regard. Cell-Free Massive MIMO has considerably improved performance with respect to a conventional small-cell scheme, whereby each user is served by a dedicated AP, in terms of both 95%-likely per-user throughput and immunity to shadow fading spatial correlation. Under uncorrelated shadow fading conditions, the cell-free scheme provides nearly 5-fold improvement in 95%-likely per-user throughput over the small-cell scheme, and 10-fold improvement when shadow fading is correlated.
  • We consider a multi-way massive multiple-input multiple-output relay network with zero-forcing processing at the relay. By taking into account the time-division duplex protocol with channel estimation, we derive an analytical approximation of the spectral efficiency. This approximation is very tight and simple which enables us to analyze the system performance, as well as, to compare the spectral efficiency with zero-forcing and maximum-ratio processing. Our results show that by using a very large number of relay antennas and with the zero-forcing technique, we can simultaneously serve many active users in the same time-frequency resource, each with high spectral efficiency.
  • We consider the Massive Multiple-Input Multiple-Output (MIMO) downlink with maximum-ratio and zero-forcing processing and time-division duplex (TDD) operation. To decode, the terminals must know their instantaneous effective channel gain. Conventionally, it is assumed that by virtue of channel hardening, this instantaneous gain is close to its average and hence that terminals can rely on knowledge of that average (also known as statistical channel information). However, in some propagation environments, such as keyhole channels, channel hardening does not hold. We propose a blind algorithm to estimate the effective channel gain at each user, that does not require any downlink pilots. We derive a capacity lower bound of each user for our proposed scheme, applicable to any propagation channel. Compared to the case of no downlink pilots (relying on channel hardening), and compared to training-based estimation using downlink pilots, our blind algorithm performs significantly better. The difference is especially pronounced in environments that do not offer channel hardening.
  • This letter proposes anti-jamming strategies based on pilot retransmission for a single user uplink massive MIMO under jamming attack. A jammer is assumed to attack the system both in the training and data transmission phases. We first derive an achievable rate which enables us to analyze the effect of jamming attacks on the system performance. Counter-attack strategies are then proposed to mitigate this effect under two different scenarios: random and deterministic jamming attacks. Numerical results illustrate our analysis and benefit of the proposed schemes.
  • This paper considers a multi-way massive multiple-input multiple-output relaying system, where single-antenna users exchange their information-bearing signals with the help of one relay station equipped with unconventionally many antennas. The relay first estimates the channels to all users through the pilot signals transmitted from them. Then, the relay uses maximum-ratio processing (i.e. maximum-ratio combining in the multiple-access phase and maximum-ratio transmission in the broadcast phase) to process the signals. A rigorous closed-form expression for the spectral efficiency is derived. The effects of the channel estimation error, the channel estimation overhead, the length of the training duration, and the randomness of the user locations are analyzed. We show that by deploying massive antenna arrays at the relay and simple maximum-ratio processing, we can serve many users in the same time-frequency resource, while maintaining a given quality-of-service for each user.
  • In this paper we consider a time-division duplex cell-free massive multiple-input multiple-output (MIMO) system where many distributed access points (APs) simultaneously serve many users. A normalized conjugate beamforming scheme, which satisfies short-term average power constraints at the APs, is proposed and analyzed taking into account the effect of imperfect channel information. We derive an approximate closed-form expression for the per-user achievable downlink rate of this scheme. We also provide, analytically and numerically, a performance comparison between the normalized conjugate beamforming and the conventional conjugate beamforming scheme in [1] (which satisfies long-term average power constraints). Normalized conjugate beamforming scheme reduces the beamforming uncertainty gain, which comes from the users' lack of the channel state information knowledge, and hence, it improves the achievable downlink rate compared to the conventional conjugate beamforming scheme.
  • In this paper, we analyze the benefits of including downlink pilots in a cell-free massive MIMO system. We derive an approximate per-user achievable downlink rate for conjugate beamforming processing, which takes into account both uplink and downlink channel estimation errors, and power control. A performance comparison is carried out, in terms of per-user net throughput, considering cell-free massive MIMO operation with and without downlink training, for different network densities. We take also into account the performance improvement provided by max-min fairness power control in the downlink. Numerical results show that, exploiting downlink pilots, the performance can be considerably improved in low density networks over the conventional scheme where the users rely on statistical channel knowledge only. In high density networks, performance improvements are moderate.
  • In this paper, we analyze the performance of the uplink communication of massive multi-cell multiple-input multiple-output (MIMO) systems under the effects of pilot contamination and delayed channels because of terminal mobility. The base stations (BSs) estimate the channels through the uplink training, and then use zero-forcing processing to decode the transmit signals from the users. The probability density function (PDF) of the signal-to-interference-plus-noise ratio is derived for any finite number of antennas. From this PDF, we derive an achievable ergodic rate with a finite number of BS antennas in closed form. Insights of the impact of the Doppler shift (due to terminal mobility) at the low signal-to-noise ratio regimes are exposed. In addition, the effects on the outage probability are investigated. Furthermore, the power scaling law and the asymptotic performance result by infinitely increasing the numbers of antennas and terminals (while their ratio is fixed) are provided. The numerical results demonstrate the performance loss for various Doppler shifts. Among the interesting observations revealed is that massive MIMO is favorable even in channel aging conditions.
  • We consider the downlink of Cell-Free Massive MIMO systems, where a very large number of distributed access points (APs) simultaneously serve a much smaller number of users. Each AP uses local channel estimates obtained from received uplink pilots and applies conjugate beamforming to transmit data to the users. We derive a closed-form expression for the achievable rate. This expression enables us to design an optimal max-min power control scheme that gives equal quality of service to all users. We further compare the performance of the Cell-Free Massive MIMO system to that of a conventional small-cell network and show that the throughput of the Cell-Free system is much more concentrated around its median compared to that of the small-cell system. The Cell-Free Massive MIMO system can provide an almost $20-$fold increase in 95%-likely per-user throughput, compared with the small-cell system. Furthermore, Cell-Free systems are more robust to shadow fading correlation than small-cell systems.
  • Massive multiple-input multiple-output (MIMO) networks, where the base stations (BSs) are equipped with large number of antennas and serve a number of users simultaneously, are very promising, but suffer from pilot contamination. Despite its importance, delayed channel state information (CSI) due to user mobility, being another degrading factor, lacks investigation in the literature. Hence, we consider an uplink model, where each BS applies zero-forcing decoder, accounting for both effects, but with the focal point on the relative users' movement with regard to the BS antennas. In this setting, analytical closed-form expressions for the sum-rate with finite number of BS antennas, and the asymptotic limits with infinite number of BS antennas epitomize the main contributions. In particular, the probability density function of the signal-to-interference-plus-noise ratio and the ergodic sum-rate are derived for any finite number of antennas. Insights of the impact of the arising Doppler shift due to user mobility into the low signal-to-noise ratio regime as well as the outage probability are obtained. Moreover, asymptotic analysis performance results in terms of infinitely increasing number of antennas, power, and both numbers of antennas and users (while their ratio is fixed) are provided. The numerical results demonstrate the performance loss in various Doppler shifts. An interesting observation is that massive MIMO is favorable even in time-varying channel conditions.
  • We consider the massive MIMO downlink with time-division duplex (TDD) operation and conjugate beamforming transmission. To reliably decode the desired signals, the users need to know the effective channel gain. In this paper, we propose a blind channel estimation method which can be applied at the users and which does not require any downlink pilots. We show that our proposed scheme can substantially outperform the case where each user has only statistical channel knowledge, and that the difference in performance is particularly large in certain types of channel, most notably keyhole channels. Compared to schemes that rely on downlink pilots, our proposed scheme yields more accurate channel estimates for a wide range of signal-to-noise ratios and avoid spending time-frequency resources on pilots.
  • We consider the uplink of massive multicell multiple-input multiple-output systems, where the base stations (BSs), equipped with massive arrays, serve simultaneously several terminals in the same frequency band. We assume that the BS estimates the channel from uplink training, and then uses the maximum ratio combining technique to detect the signals transmitted from all terminals in its own cell. We propose an optimal resource allocation scheme which jointly selects the training duration, training signal power, and data signal power in order to maximize the sum spectral efficiency, for a given total energy budget spent in a coherence interval. Numerical results verify the benefits of the optimal resource allocation scheme. Furthermore, we show that more training signal power should be used at low signal-to-noise ratio (SNRs), and vice versa at high SNRs. Interestingly, for the entire SNR regime, the optimal training duration is equal to the number of terminals.
  • We consider a multipair decode-and-forward relay channel, where multiple sources transmit simultaneously their signals to multiple destinations with the help of a full-duplex relay station. We assume that the relay station is equipped with massive arrays, while all sources and destinations have a single antenna. The relay station uses channel estimates obtained from received pilots and zero-forcing (ZF) or maximum-ratio combining/maximum-ratio transmission (MRC/MRT) to process the signals. To reduce significantly the loop interference effect, we propose two techniques: i) using a massive receive antenna array; or ii) using a massive transmit antenna array together with very low transmit power at the relay station. We derive an exact achievable rate in closed-form for MRC/MRT processing and an analytical approximation of the achievable rate for ZF processing. This approximation is very tight, especially for large number of relay station antennas. These closed-form expressions enable us to determine the regions where the full-duplex mode outperforms the half-duplex mode, as well as, to design an optimal power allocation scheme. This optimal power allocation scheme aims to maximize the energy efficiency for a given sum spectral efficiency and under peak power constraints at the relay station and sources. Numerical results verify the effectiveness of the optimal power allocation scheme. Furthermore, we show that, by doubling the number of transmit/receive antennas at the relay station, the transmit power of each source and of the relay station can be reduced by 1.5dB if the pilot power is equal to the signal power, and by 3dB if the pilot power is kept fixed, while maintaining a given quality-of-service.
  • Favorable propagation, defined as mutual orthogonality among the vector-valued channels to the terminals, is one of the key properties of the radio channel that is exploited in Massive MIMO. However, there has been little work that studies this topic in detail. In this paper, we first show that favorable propagation offers the most desirable scenario in terms of maximizing the sum-capacity. One useful proxy for whether propagation is favorable or not is the channel condition number. However, this proxy is not good for the case where the norms of the channel vectors may not be equal. For this case, to evaluate how favorable the propagation offered by the channel is, we propose a ``distance from favorable propagation'' measure, which is the gap between the sum-capacity and the maximum capacity obtained under favorable propagation. Secondly, we examine how favorable the channels can be for two extreme scenarios: i.i.d. Rayleigh fading and uniform random line-of-sight (UR-LoS). Both environments offer (nearly) favorable propagation. Furthermore, to analyze the UR-LoS model, we propose an urns-and-balls model. This model is simple and explains the singular value spread characteristic of the UR-LoS model well.
  • We consider a massive MU-MIMO downlink time-division duplex system where a base station (BS) equipped with many antennas serves several single-antenna users in the same time-frequency resource. We assume that the BS uses linear precoding for the transmission. To reliably decode the signals transmitted from the BS, each user should have an estimate of its channel. In this work, we consider an efficient channel estimation scheme to acquire CSI at each user, called beamforming training scheme. With the beamforming training scheme, the BS precodes the pilot sequences and forwards to all users. Then, based on the received pilots, each user uses minimum mean-square error channel estimation to estimate the effective channel gains. The channel estimation overhead of this scheme does not depend on the number of BS antennas, and is only proportional to the number of users. We then derive a lower bound on the capacity for maximum-ratio transmission and zero-forcing precoding techniques which enables us to evaluate the spectral efficiency taking into account the spectral efficiency loss associated with the transmission of the downlink pilots. Comparing with previous work where each user uses only the statistical channel properties to decode the transmitted signals, we see that the proposed beamforming training scheme is preferable for moderate and low-mobility environments.
  • We consider a multi-pair relay channel where multiple sources simultaneously communicate with destinations using a relay. Each source or destination has only a single antenna, while the relay is equipped with a very large antenna array. We investigate the power efficiency of this system when maximum ratio combining/maximal ratio transmission (MRC/MRT) or zero-forcing (ZF) processing is used at the relay. Using a very large array, the transmit power of each source or relay (or both) can be made inversely proportional to the number of relay antennas while maintaining a given quality-of-service. At the same time, the achievable sum rate can be increased by a factor of the number of source-destination pairs. We show that when the number of antennas grows to infinity, the asymptotic achievable rates of MRC/MRT and ZF are the same if we scale the power at the sources. Depending on the large scale fading effect, MRC/MRT can outperform ZF or vice versa if we scale the power at the relay.
  • We consider the uplink of a multicell multiuser multiple-input multiple-output system where the channel experiences both small and large-scale fading. The data detection is done by using the linear zero-forcing technique, assuming the base station (BS) has perfect channel state information. We derive new, exact closed-form expressions for the uplink rate, symbol error rate, and outage probability per user, as well as a lower bound on the achievable rate. This bound is very tight and becomes exact in the large-number-of-antennas limit. We further study the asymptotic system performance in the regimes of high signal-to-noise ratio (SNR), large number of antennas, and large number of users per cell. We show that at high SNRs, the system is interference-limited and hence, we cannot improve the system performance by increasing the transmit power of each user. Instead, by increasing the number of BS antennas, the effects of interference and noise can be reduced, thereby improving the system performance. We demonstrate that, with very large antenna arrays at the BS, the transmit power of each user can be made inversely proportional to the number of BS antennas while maintaining a desired quality-of-service. Numerical results are presented to verify our analysis.