• ### Particle identification studies with a full-size 4-GEM prototype for the ALICE TPC upgrade(1805.03234)

May 8, 2018 physics.ins-det
A large Time Projection Chamber is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019/20, the LHC will deliver Pb beams colliding at an interaction rate of about 50 kHz, which is about a factor of 50 above the present readout rate of the TPC. This will result in a significant improvement on the sensitivity to rare probes that are considered key observables to characterize the QCD matter created in such collisions. In order to make full use of this luminosity, the currently used gated Multi-Wire Proportional Chambers will be replaced by continuously operated readout detectors employing Gas Electron Multiplier technology, while retaining the performance in terms of particle identification via the measurement of the specific energy loss by ionization d$E$/d$x$. A full-size readout chamber prototype was assembled in 2014 featuring a stack of four GEM foils as an amplification stage. The d$E$/d$x$ resolution of the prototype, evaluated in a test beam campaign at the CERN PS, complies with both the performance of the currently operated MWPC-based readout chambers and the challenging requirements of the ALICE TPC upgrade program. Detailed simulations of the readout system are able to reproduce the data.
• ### Studies of the effect of rate on gain for straw tube detector(1709.08030)

Sept. 23, 2017 hep-ex, physics.ins-det
Basic R & D have been carried out with one small straw tube detector prototype with premixed gas of Ar+CO2 in 70:30 and 90:10 ratio. The gain and the energy resolution are measured with Fe55 X-ray source. Effect of temperature and pressure on these parameters are measured. The variation of gain and energy resolution with rate per unit length are also measured. The details of the test set-up, the method of measurement and the test results are presented in this paper.
• ### Longitudinal Wobbling in $^{133}$La(1608.07840)

May 27, 2017 nucl-ex, nucl-th
Excited states of $^{133}$La have been investigated to search for the wobbling excitation mode in the low-spin regime. Wobbling bands with $n_\omega$ = 0 and 1 are identified along with the interconnecting $\Delta I$ = 1, $E2$ transitions, which are regarded as one of the characteristic features of the wobbling motion. An increase in wobbling frequency with spin implies longitudinal wobbling for $^{133}$La, in contrast with the case of transverse wobbling observed in $^{135}$Pr. This is the first observation of a longitudinal wobbling band in nuclei. The experimental observations are accounted for by calculations using the quasiparticle-triaxial-rotor (QTR) model, which attribute the appearance of longitudinal wobbling to the early alignment of a $\pi=+$ proton pair.
• Substantial experimental and theoretical efforts worldwide are devoted to explore the phase diagram of strongly interacting matter. At LHC and top RHIC energies, QCD matter is studied at very high temperatures and nearly vanishing net-baryon densities. There is evidence that a Quark-Gluon-Plasma (QGP) was created at experiments at RHIC and LHC. The transition from the QGP back to the hadron gas is found to be a smooth cross over. For larger net-baryon densities and lower temperatures, it is expected that the QCD phase diagram exhibits a rich structure, such as a first-order phase transition between hadronic and partonic matter which terminates in a critical point, or exotic phases like quarkyonic matter. The discovery of these landmarks would be a breakthrough in our understanding of the strong interaction and is therefore in the focus of various high-energy heavy-ion research programs. The Compressed Baryonic Matter (CBM) experiment at FAIR will play a unique role in the exploration of the QCD phase diagram in the region of high net-baryon densities, because it is designed to run at unprecedented interaction rates. High-rate operation is the key prerequisite for high-precision measurements of multi-differential observables and of rare diagnostic probes which are sensitive to the dense phase of the nuclear fireball. The goal of the CBM experiment at SIS100 (sqrt(s_NN) = 2.7 - 4.9 GeV) is to discover fundamental properties of QCD matter: the phase structure at large baryon-chemical potentials (mu_B > 500 MeV), effects of chiral symmetry, and the equation-of-state at high density as it is expected to occur in the core of neutron stars. In this article, we review the motivation for and the physics programme of CBM, including activities before the start of data taking in 2022, in the context of the worldwide efforts to explore high-density QCD matter.
• ### Physics Behind Precision(1703.01626)

March 5, 2017 hep-ph, hep-ex
This document provides a writeup of contributions to the FCC-ee mini-workshop on "Physics behind precision" held at CERN, on 2-3 February 2016.
• ### Coherent and incoherent aspects of polariton dynamics in semiconductor microcavities(1611.04770)

Nov. 15, 2016 cond-mat.mes-hall
The interaction between coherent polaritons and incoherent excitons plays an important role in polariton physics. Using resonant pump-probe spectroscopy with selective excitation of single polariton branches, we investigate the different dephasing mechanisms responsible for generating a long-lived exciton reservoir. As expected, pumping the upper polariton results in a strong dephasing process that leads to the generation of a long lived reservoir. Unexpectedly, we observe an efficient reservoir creation while exciting only the lower polariton branch when the detuning is increased towards positive detuning. We propose a simple theoretical model, the polaritonic Bloch equations, to describe the dynamics of the system.
• ### Building of a 4-channel TTL scaler for counting detector signals(1608.00563)

July 30, 2016 hep-ex, physics.ins-det
A scaler has been fabricated to count the signals from any radiation de- tector. It can count signals of frequency up to 140 kHz. Transistor Transistor Logic (TTL) is used in this scaler. In this article the details of the design, fabrication and operation processes of the scaler is presented.
• ### Long-term stability test of a triple GEM detector(1608.00562)

July 30, 2016 hep-ex, physics.ins-det
The main aim of the study is to perform the long-term stability test of gain of the single mask triple GEM detector. A simple method is used for this long- term stability test using a radioactive X-ray source with high activity. The test is continued till accumulation of charge per unit area > 12.0 mC/mm2. The details of the chamber fabrication, the test set-up, the method of measurement and the test results are presented in this paper.
• ### Design and fabrication of a data logger for atmospheric pressure, temperature and relative humidity for gas-filled detector development(1507.03575)

July 12, 2015 physics.ins-det
A novel instrument has been developed to monitor and record the ambient pa- rameters such as temperature, atmospheric pressure and relative humidity. These parameters are very essential for understanding the characteristics such as gain of gas filled detectors like Gas Electron Multiplier (GEM) and Multi Wire Propor- tional Counter (MWPC). In this article the details of the design, fabrication and operation processes of the device has been presented.
• ### Systematic measurements of the gain and the energy resolution of single and double mask GEM detectors(1505.07767)

May 26, 2015 hep-ex, physics.ins-det
Systematic studies on the gain and the energy resolution have been carried out varying the voltage across the GEM foils for both single mask and double mask triple GEM detector prototypes. Variation of the gain and the energy resolution have also been measured varying either the drift voltage, transfer voltage and induction voltage keeping other voltages constant. The results of the systematic measurements has been presented.
• ### Characterizations of GEM detector prototype(1505.07768)

May 26, 2015 hep-ex, physics.ins-det
At NISER-IoP detector laboratory an initiative is taken to build and test Gas Electron Multiplier (GEM) detectors for ALICE experiment. The optimisation of the gas flow rate and the long-term stability test of the GEM detector are performed. The method and test results are presented.
• ### A simple technique for gamma ray and cosmic ray spectroscopy using plastic scintillator(1407.7181)

April 10, 2015 hep-ex, physics.ins-det
A new and simple technique has been developed using plastic scintillator detectors for gamma ray and cosmic ray spectroscopy without single channel analyzer (SCA) or multichannel analyzer (MCA). In these experiments only a leading edge discriminator (LED) and NIM scalers have been used. Energy calibration of gamma spectra in plastic scintillators has been done using Co$^{60}$ and Cs$^{137}$ sources. The details experimental technique, analysis procedure and experimental results has been presented in this article.
• ### Measurement of spark probability of GEM detector for CBM muon chamber (MUCH)(1504.00001)

March 31, 2015 hep-ex, nucl-ex, physics.ins-det
The stability of triple GEM detector setups in an environment of high energetic showers is studied. To this end the spark probability in a shower environment is compared to the spark probability in a pion beam.
• ### Resonant Slepton Production Yields CMS $eejj$ and $ejj$ Missing $p_T$ Excesses(1410.5947)

Dec. 4, 2014 hep-ph, hep-ex
Recent CMS searches for di-leptoquark production report local excesses of 2.4$\sigma$ in a $eejj$ channel and 2.6$\sigma$ in a $ejj$ missing $p_T$ channel. Here, we simultaneously explain both excesses with resonant slepton production in ${\mathcal R}-$parity violating supersymmetry (SUSY). We consider resonant slepton production, which decays to a lepton and a chargino/neutralino, followed by three-body decays of the neutralino/chargino via an $\mathcal{R}-$parity violating coupling. There are regions of parameter space which are also compatible at the 95% confidence level (CL) with a 2.8$\sigma$ $eejj$ excess in a recent CMS $W_R$ search, while being compatible with other direct search constraints. Phase-II of the GERDA neutrinoless double beta decay ($0\nu\beta\beta$) experiment will probe a sizeable portion of the good-fit region.
• ### Study of the characteristics of GEM detectors for the future FAIR experiment CBM(1408.0075)

Aug. 1, 2014 nucl-ex, physics.ins-det
Characteristics of triple GEM detector have been studied systematically. The variation of the effective gain and energy resolution of GEM with variation of the applied voltage has been measured with Fe55 X-ray source for different gas mixtures and with different gas flow rates. Long-term test of the GEM has also been performed.
• ### Development of Multi-gap Resistive Plate Chamber (MRPC) for medical imaging(1408.0280)

The low cost and high resolution Multi-gap Resistive Plate Chamber (MRPC) opens up a new possibility to find an efficient alternative detector for the Time of Flight (TOF) based Positron Emission Tomography, where the sensitivity of the system depends largely on the time resolution of the detector. In a layered structure, suitable converters can be used to increase the photon detection efficiency. In this paper results of the cosmic ray test of a four-gap bakelite-based prototype MRPC operated in streamer mode and six-gap glass-based MRPC operated in avalanche mode are discussed.
• ### Calibration and performance of the STAR Muon Telescope Detector using cosmic rays(1402.1078)

We report the timing and spatial resolution from the Muon Telescope Detector (MTD) installed in the STAR experiment at RHIC. Cosmic ray muons traversing the STAR detector have an average transverse momentum of 6 GeV/c. Due to their very small multiple scattering, these cosmic muons provide an ideal tool to calibrate the detectors and measure their timing and spatial resolution. The values obtained were ~100 ps and ~1-2 cm, respectively. These values are comparable to those obtained from cosmic-ray bench tests and test beams.
• ### Exploring the origin of degenerate doublet bands in $^{106}$Ag(1310.7731)

Oct. 29, 2013 nucl-ex
The electromagnetic transition probabilities of the excited levels for the two nearly degenerate bands of $^{106}$Ag have been measured using the Doppler Shift Attenuation Method. A comparison with the calculated values using triaxial projected shell model approach indicates that these bands originate from two different quasi-particle configurations but constructed from the same mean-field deformation.
• ### Development of a GEM based detector for the CBM Muon Chamber (MUCH)(1310.0642)

Oct. 3, 2013 hep-ex, physics.ins-det
The characteristics of triple GEM detectors have been studied systematically by using cosmic ray muons. The minimum ionizing particle (MIP) spectra has been taken for different GEM voltage setting. Efficiency of GEM detector has been measured for cosmic ray. At high rate operation of GEMs the value of the protection resistor influences the gain and the stability. This feature has been investigated varying both the rate and the value of the protection resistor. This measurement has been performed using both X-ray generator and Fe55 source. The ageing and long-term stability of GEM based detectors has been studied employing both X-ray generator and Fe55 source. The ageing study of one GEM module is performed by using a 8 keV Cu X-ray generator to verify the stability and integrity of the GEM detectors over a longer period of time. The accumulated charge on the detector is calculated from the rate of the X-ray and the average gain of the detector. The details of the measurement and results has been described in this article.
• ### Measurement of electrical properties of electrode materials for the bakelite Resistive Plate Chambers(1206.5894)

June 26, 2012 physics.ins-det
Single gap (gas gap 2 mm) bakelite Resistive Plate Chamber (RPC) modules of various sizes from 10 cm \times 10 cm to 1 m \times 1 m have been fabricated, characterized and optimized for efficiency and time resolution. Thin layers of different grades of silicone compound are applied to the inner electrode surfaces to make them smooth and also to reduce the surface resistivity. In the silicone coated RPCs an efficiency > 90% and time resolution \sim 2 ns (FWHM) have been obtained for both the streamer and the avalanche mode of operation. Before fabrication of detectors the electrical properties such as bulk resistivity and surface resistivity of the electrode materials are measured carefully. Effectiveness of different silicone coating in modifying the surface resistivity was evaluated by an instrument developed for monitoring the I-V curve of a high resistive surface. The results indicate definite correlation of the detector efficiency for the atmospheric muons and the RPC noise rates with the surface resistivity and its variation with the applied bias voltage. It was also found that the surface resistivity varies for different grades of silicone material applied as coating, and the results are found to be consistent with the detector efficiency and noise rate measurements done with these RPCs.
• ### Performances of silicone coated high resistive bakelite RPC(1206.5627)

June 25, 2012 physics.ins-det
Performances of several single gap (gas gap 2 mm) prototype Resistive Plate Chambers (RPC) made of high resistive ({\rho} \sim 1010 - 1012 {\Omega} cm) bakelite, commercially available in India have been studied in recent times. To make the inner electrode surfaces smooth, a thin coating of silicone has been applied. An efficiency > 90% and time resolution \sim 2 ns (FWHM) have been obtained for both the streamer and the avalanche mode. The induced charge distributions of those silicone coated RPC are studied and the results are presented. A numerical study on the effect of surface roughness of the resistive electrodes on the electric field of the device has been carried out using Garfield-neBEM code. A few results for a simplified model representing surface roughness, measured using a surface profilometer for the bakelite surfaces, have also been presented.
• ### A Josephson Quantum Electron Pump(1102.4207)

A macroscopic fluid pump works according to the law of Newtonian mechanics and transfers a large number of molecules per cycle (of the order of 10^23). By contrast, a nano-scale charge pump can be thought as the ultimate miniaturization of a pump, with its operation being subject to quantum mechanics and with only few electrons or even fractions of electrons transfered per cycle. It generates a direct current in the absence of an applied voltage exploiting the time-dependence of some properties of a nano-scale conductor. The idea of pumping in nanostructures was discussed theoretically a few decades ago [1-4]. So far, nano-scale pumps have been realised only in system exhibiting strong Coulombic effects [5-12], whereas evidence for pumping in the absence of Coulomb-blockade has been elusive. A pioneering experiment by Switkes et al. [13] evidenced the difficulty of modulating in time the properties of an open mesoscopic conductor at cryogenic temperatures without generating undesired bias voltages due to stray capacitances [14,15]. One possible solution to this problem is to use the ac Josephson effect to induce periodically time-dependent Andreev-reflection amplitudes in a hybrid normal-superconducting system [16]. Here we report the experimental detection of charge flow in an unbiased InAs nanowire (NW) embedded in a superconducting quantum interference device (SQUID). In this system, pumping may occur via the cyclic modulation of the phase of the order parameter of different superconducting electrodes. The symmetry of the current with respect to the enclosed magnetic flux [17,18] and bias SQUID current is a discriminating signature of pumping. Currents exceeding 20 pA are measured at 250 mK, and exhibit symmetries compatible with a pumping mechanism in this setup which realizes a Josephson quantum electron pump (JQEP).
• ### Electronic transport properties of ternary Cd1-xZnxS nanowire network(0909.3480)

Sept. 18, 2009 cond-mat.mes-hall
We present electronic transport characteristics of ternary alloy Cd1-xZnxS nanowire networks in the dark and under white light illumination. Compared to the negligible dark current, we observed a photocurrent enhancement up to 4 orders of magnitude at intensity of 460 mW/cm2. The time constant of the dynamic photoresponse is ~5 sec. The current-voltage characteristics at different intensities show Ohmic behavior at low bias and space charge limited conduction (SCLC) at higher bias voltages. The SCLC behavior and slow time response indicate that the charge transport is dominated by tunneling at the percolating inter-nanowire junctions.
• ### Performances of linseed oil-free bakelite RPC prototypes with cosmic ray muons(0907.2976)

July 17, 2009 hep-ex, physics.ins-det
A comparative study has been performed on Resistive Plate Chambers (RPC) made of two different grades of bakelite paper laminates, produced and commercially available in India. The chambers, operated in the streamer mode using argon, tetrafluroethane and isobutane in 34:59:7 mixing ratio, are tested for the efficiency and the stability with cosmic rays. A particular grade of bakelite (P-120, NEMA LI-1989 Grade XXX), used for high voltage insulation in humid conditions, was found to give satisfactory performance with stable efficiency of > 96% continuously for more than 130 days. A thin coating of silicone fluid on the inner surfaces of the bakelite RPC is found to be necessary for operation of the detector.
• ### Development of linseed oil-free bakelite resistive plate chambers(0907.2978)

July 17, 2009 hep-ex, physics.ins-det
In this paper we would like to present a few characteristics of the Resistive Plate Chambers (RPC) made of a particular grade of bakelite paper laminates (P-120, NEMA LI-1989 Grade XXX), produced and commercially available in India. This particular grade is used for high voltage insulation in humid conditions. The chambers are tested with cosmic rays in the streamer mode using argon, tetrafluroethane and isobutane in 34:59:7 mixing ratio. In the first set of detectors made with such grade, a thin coating of silicone fluid on the inner surfaces of the bakelite was found to be necessary for operation of the detector. Those silicone coated RPCs were found to give satisfactory performance with stable efficiency of >90% continuously for a long period as reported earlier. Results of the crosstalk measurement of these silicone coated RPC will be presented in this paper. Very recently RPCs made with the same grade of bakelite but having better surface finish, are found to give equivalent performance even without any coating inside. Preliminary results of this type of RPCs are also being presented.