-
The Advanced Photon Source is in the process of up-grading its storage ring
from a double-bend to a multi-bend lattice as part of the APS Upgrade Project
(APS-U). A swap-out injection scheme is planned for the APS-U to keep a
constant beam current and to enable a small dynamic aperture. A novel concept
that cancels out the effect of leakage field inside the stored beam chamber was
introduced in the design of the septum magnet. As a result, the horizontal
deflecting angle of the stored beam was reduced to below 1 micro-rad with a 2
mm septum thick-ness and 1.06T normal injection field. The concept helped to
minimize the integrated skew quadrupole field and normal sextupole fields
inside stored beam chamber as well. The designed septum magnet deflects the
injected electron beam by 89 mrad with a ring energy of 6 GeV. The stored beam
chamber has an 8 mm x 6 mm super-ellipsoidal aperture. The magnet is straight;
however, it is tilted in yaw, roll, and pitch from the stored beam cham-ber to
meet the on axis swap out injection requirements for the APS-U lattice.
-
A beam optics scheme has been designed for the Future Circular Collider-e+e-
(FCC-ee). The main characteristics of the design are: beam energy 45 to 175
GeV, 100 km circumference with two interaction points (IPs) per ring,
horizontal crossing angle of 30 mrad at the IP and the crab-waist scheme [1]
with local chromaticity correction. The crab-waist scheme is implemented within
the local chromaticity correction system without additional sextupoles, by
reducing the strength of one of the two sextupoles for vertical chromatic
correction at each side of the IP. So-called "tapering" of the magnets is
applied, which scales all fields of the magnets according to the local beam
energy to compensate for the effect of synchrotron radiation (SR) loss along
the ring. An asymmetric layout near the interaction region reduces the critical
energy of SR photons on the incoming side of the IP to values below 100 keV,
while matching the geometry to the beam line of the FCC proton collider
(FCC-hh) [2] as closely as possible. Sufficient transverse/longitudinal dynamic
aperture (DA) has been obtained, including major dynamical effects, to assure
an adequate beam lifetime in the presence of beamstrahlung and top-up
injection. In particular, a momentum acceptance larger than +/-2% has been
obtained, which is better than the momentum acceptance of typical collider
rings by about a factor of 2. The effects of the detector solenoids including
their compensation elements are taken into account as well as synchrotron
radiation in all magnets. The optics presented in this paper is a step toward a
full conceptual design for the collider. A number of issues have been
identified for further study.
-
The ion collider ring of Jefferson Lab Electron-Ion Collider (JLEIC)
accommodates a wide range of ion energies, from 20 to 100 GeV for protons or
from 8 to 40 GeV per nucleon for lead ions. In this medium energy range, ions
are not fully relativistic, which means values of their relativistic beta are
slightly below 1, leading to an energy dependence of revolution time of the
collider ring. On the other hand, electrons with energy 3 GeV and above are
already ultra-relativistic such that their speeds are effectively equal to the
speed of light. The difference in speeds of colliding electrons and ions in
JLEIC, when translated into a path-length difference necessary to maintain the
same timing between electron and ion bunches, is quite large. In this paper, we
explore schemes for synchronizing the electron and ion bunches at a collision
point as the ion energy is varied.
-
This work is on the Physics of the B Factories. Part A of this book contains
a brief description of the SLAC and KEK B Factories as well as their detectors,
BaBar and Belle, and data taking related issues. Part B discusses tools and
methods used by the experiments in order to obtain results. The results
themselves can be found in Part C.
Please note that version 3 on the archive is the auxiliary version of the
Physics of the B Factories book. This uses the notation alpha, beta, gamma for
the angles of the Unitarity Triangle. The nominal version uses the notation
phi_1, phi_2 and phi_3. Please cite this work as Eur. Phys. J. C74 (2014) 3026.
-
The FCC (Future Circular Collider) study represents a vision for the next
large project in high energy physics, comprising an 80-100 km tunnel that can
house a future 100 TeV hadron collider. The study also includes a high
luminosity e+e- collider operating in the centre-of-mass energy range of 90-350
GeV as a possible intermediate step, the FCC-ee. The FCC-ee aims at definitive
electro-weak precision measurements of the Z, W, H and top particles, and
search for rare phenomena. Although FCC-ee is based on known technology, the
goal performance in luminosity and energy calibration make it quite
challenging. During 2014 the study went through an exploration phase. The study
has now entered its second year and the aim is to produce a conceptual design
report during the next three to four years. We here report on progress since
the last IPAC conference.
-
This document summarizes the design of Jefferson Lab's electron-ion collider,
MEIC, as of January 20, 2015, and describes the facility whose cost was
estimated for the United States Department of Energy Nuclear Sciences Advisory
Committee EIC cost review of January 26-28, 2015. In particular, each of the
main technical systems within the collider is presented to the level of the
best current information.
-
In this Technical Design Report (TDR) we describe the SuperB detector that
was to be installed on the SuperB e+e- high luminosity collider. The SuperB
asymmetric collider, which was to be constructed on the Tor Vergata campus near
the INFN Frascati National Laboratory, was designed to operate both at the
Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1}
and at the tau/charm production threshold with a luminosity of 10^{35}
cm^{-2}s^{-1}. This high luminosity, producing a data sample about a factor 100
larger than present B Factories, would allow investigation of new physics
effects in rare decays, CP Violation and Lepton Flavour Violation. This
document details the detector design presented in the Conceptual Design Report
(CDR) in 2007. The R&D and engineering studies performed to arrive at the full
detector design are described, and an updated cost estimate is presented.
A combination of a more realistic cost estimates and the unavailability of
funds due of the global economic climate led to a formal cancelation of the
project on Nov 27, 2012.
-
The present note relies on the recently published conceptual design report of
the LHeC and extends the first contribution to the European strategy debate in
emphasising the role of the LHeC to complement and complete the high luminosity
LHC programme. The brief discussion therefore focuses on the importance of high
precision PDF and $\alpha_s$ determinations for the physics beyond the Standard
Model (GUTs, SUSY, Higgs). Emphasis is also given to the importance of high
parton density phenomena in nuclei and their relevance to the heavy ion physics
programme at the LHC.
-
This document provides a brief overview of the recently published report on
the design of the Large Hadron Electron Collider (LHeC), which comprises its
physics programme, accelerator physics, technology and main detector concepts.
The LHeC exploits and develops challenging, though principally existing,
accelerator and detector technologies. This summary is complemented by brief
illustrations of some of the highlights of the physics programme, which relies
on a vastly extended kinematic range, luminosity and unprecedented precision in
deep inelastic scattering. Illustrations are provided regarding high precision
QCD, new physics (Higgs, SUSY) and electron-ion physics. The LHeC is designed
to run synchronously with the LHC in the twenties and to achieve an integrated
luminosity of O(100) fb$^{-1}$. It will become the cleanest high resolution
microscope of mankind and will substantially extend as well as complement the
investigation of the physics of the TeV energy scale, which has been enabled by
the LHC.
-
The physics programme and the design are described of a new collider for
particle and nuclear physics, the Large Hadron Electron Collider (LHeC), in
which a newly built electron beam of 60 GeV, up to possibly 140 GeV, energy
collides with the intense hadron beams of the LHC. Compared to HERA, the
kinematic range covered is extended by a factor of twenty in the negative
four-momentum squared, $Q^2$, and in the inverse Bjorken $x$, while with the
design luminosity of $10^{33}$ cm$^{-2}$s$^{-1}$ the LHeC is projected to
exceed the integrated HERA luminosity by two orders of magnitude. The physics
programme is devoted to an exploration of the energy frontier, complementing
the LHC and its discovery potential for physics beyond the Standard Model with
high precision deep inelastic scattering measurements. These are designed to
investigate a variety of fundamental questions in strong and electroweak
interactions. The physics programme also includes electron-deuteron and
electron-ion scattering in a $(Q^2, 1/x)$ range extended by four orders of
magnitude as compared to previous lepton-nucleus DIS experiments for novel
investigations of neutron's and nuclear structure, the initial conditions of
Quark-Gluon Plasma formation and further quantum chromodynamic phenomena. The
LHeC may be realised either as a ring-ring or as a linac-ring collider. Optics
and beam dynamics studies are presented for both versions, along with technical
design considerations on the interaction region, magnets and further
components, together with a design study for a high acceptance detector. Civil
engineering and installation studies are presented for the accelerator and the
detector. The LHeC can be built within a decade and thus be operated while the
LHC runs in its high-luminosity phase. It thus represents a major opportunity
for progress in particle physics exploiting the investment made in the LHC.
-
The UA9 experimental equipment was installed in the CERN-SPS in March '09
with the aim of investigating crystal assisted collimation in coasting mode.
Its basic layout comprises silicon bent crystals acting as primary
collimators mounted inside two vacuum vessels. A movable 60 cm long block of
tungsten located downstream at about 90 degrees phase advance intercepts the
deflected beam.
Scintillators, Gas Electron Multiplier chambers and other beam loss monitors
measure nuclear loss rates induced by the interaction of the beam halo in the
crystal. Roman pots are installed in the path of the deflected particles and
are equipped with a Medipix detector to reconstruct the transverse distribution
of the impinging beam. Finally UA9 takes advantage of an LHC-collimator
prototype installed close to the Roman pot to help in setting the beam
conditions and to analyze the efficiency to deflect the beam. This paper
describes in details the hardware installed to study the crystal collimation
during 2010.
-
A Super Flavor Factory, an asymmetric energy e+e- collider with a luminosity
of order 10^36 cm-2s-1, can provide a sensitive probe of new physics in the
flavor sector of the Standard Model. The success of the PEP-II and KEKB
asymmetric colliders in producing unprecedented luminosity above 10^34 cm-2s-1
has taught us about the accelerator physics of asymmetric e+e- colliders in a
new parameter regime. Furthermore, the success of the SLAC Linear Collider and
the subsequent work on the International Linear Collider allow a new
Super-Flavor collider to also incorporate linear collider techniques. This note
describes the parameters of an asymmetric Flavor-Factory collider at a
luminosity of order 10^36 cm-2s-1 at the Upsilon(4S) resonance and about 10^35
cm-2s-1 at the Tau production threshold. Such a collider would produce an
integrated luminosity of about 10,000 fb-1 (10 ab-1) in a running year (10^7
sec) at the Upsilon(4S) resonance.
-
This paper is based on the outcome of the activity that has taken place
during the recent workshop on "SuperB in Italy" held in Frascati on November
11-12, 2005. The workshop was opened by a theoretical introduction of Marco
Ciuchini and was structured in two working groups. One focused on the machine
and the other on the detector and experimental issues.
The present status on CP is mainly based on the results achieved by BaBar and
Belle. Estabilishment of the indirect CP violation in B sector in 2001 and of
the direct CP violation in 2004 thanks to the success of PEP-II and KEKB e+e-
asymmetric B Factories operating at the center of mass energy corresponding to
the mass of the Y(4s). With the two B Factories taking data, the Unitarity
Triangle is now beginning to be overconstrained by improving the measurements
of the sides and now also of the angles alpha, and gamma. We are also in
presence of the very intriguing results about the measurements of sin(2 beta)
in the time dependent analysis of decay channels via penguin loops, where b -->
s sbar s and b --> s dbar d. Tau physics, in particular LFV search, as well as
charm and ISR physics are important parts of the scientific program of a SuperB
Factory. The physics case together with possible scenarios for the high
luminosity SuperB Factory based on the concepts of the Linear Collider and the
related experimental issues are discussed.
-
The successful commissioning and operation of the PEP-II asymmetric e+e-
collider motivated further studies to increase luminosity. In this paper, we
discuss a modification of the PEP-II lattice to reduce the vertical beta
function at the Interaction Point (IP) from the design value of 1.5cm to 1.0cm.
This could potentially reduce the colliding beam size, increase particle
density at the IP and the probability of beam-beam interactions. In this paper,
we outline the optics modifications, discuss tracking simulations, and overview
machine implementation.
A beam optics scheme has been designed for the Future Circular Collider-e+e- (FCC-ee). The main characteristics of the design are: beam energy 45 to 175 GeV, 100 km circumference with two interaction points (IPs) per ring, horizontal crossing angle of 30 mrad at the IP and the crab-waist scheme [1] with local chromaticity correction. The crab-waist scheme is implemented within the local chromaticity correction system without additional sextupoles, by reducing the strength of one of the two sextupoles for vertical chromatic correction at each side of the IP. So-called "tapering" of the magnets is applied, which scales all fields of the magnets according to the local beam energy to compensate for the effect of synchrotron radiation (SR) loss along the ring. An asymmetric layout near the interaction region reduces the critical energy of SR photons on the incoming side of the IP to values below 100 keV, while matching the geometry to the beam line of the FCC proton collider (FCC-hh) [2] as closely as possible. Sufficient transverse/longitudinal dynamic aperture (DA) has been obtained, including major dynamical effects, to assure an adequate beam lifetime in the presence of beamstrahlung and top-up injection. In particular, a momentum acceptance larger than +/-2% has been obtained, which is better than the momentum acceptance of typical collider rings by about a factor of 2. The effects of the detector solenoids including their compensation elements are taken into account as well as synchrotron radiation in all magnets. The optics presented in this paper is a step toward a full conceptual design for the collider. A number of issues have been identified for further study.
In this Technical Design Report (TDR) we describe the SuperB detector that was to be installed on the SuperB e+e- high luminosity collider. The SuperB asymmetric collider, which was to be constructed on the Tor Vergata campus near the INFN Frascati National Laboratory, was designed to operate both at the Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1} and at the tau/charm production threshold with a luminosity of 10^{35} cm^{-2}s^{-1}. This high luminosity, producing a data sample about a factor 100 larger than present B Factories, would allow investigation of new physics effects in rare decays, CP Violation and Lepton Flavour Violation. This document details the detector design presented in the Conceptual Design Report (CDR) in 2007. The R&D and engineering studies performed to arrive at the full detector design are described, and an updated cost estimate is presented. A combination of a more realistic cost estimates and the unavailability of funds due of the global economic climate led to a formal cancelation of the project on Nov 27, 2012.
The present note relies on the recently published conceptual design report of the LHeC and extends the first contribution to the European strategy debate in emphasising the role of the LHeC to complement and complete the high luminosity LHC programme. The brief discussion therefore focuses on the importance of high precision PDF and $\alpha_s$ determinations for the physics beyond the Standard Model (GUTs, SUSY, Higgs). Emphasis is also given to the importance of high parton density phenomena in nuclei and their relevance to the heavy ion physics programme at the LHC.
This document provides a brief overview of the recently published report on the design of the Large Hadron Electron Collider (LHeC), which comprises its physics programme, accelerator physics, technology and main detector concepts. The LHeC exploits and develops challenging, though principally existing, accelerator and detector technologies. This summary is complemented by brief illustrations of some of the highlights of the physics programme, which relies on a vastly extended kinematic range, luminosity and unprecedented precision in deep inelastic scattering. Illustrations are provided regarding high precision QCD, new physics (Higgs, SUSY) and electron-ion physics. The LHeC is designed to run synchronously with the LHC in the twenties and to achieve an integrated luminosity of O(100) fb$^{-1}$. It will become the cleanest high resolution microscope of mankind and will substantially extend as well as complement the investigation of the physics of the TeV energy scale, which has been enabled by the LHC.
The physics programme and the design are described of a new collider for particle and nuclear physics, the Large Hadron Electron Collider (LHeC), in which a newly built electron beam of 60 GeV, up to possibly 140 GeV, energy collides with the intense hadron beams of the LHC. Compared to HERA, the kinematic range covered is extended by a factor of twenty in the negative four-momentum squared, $Q^2$, and in the inverse Bjorken $x$, while with the design luminosity of $10^{33}$ cm$^{-2}$s$^{-1}$ the LHeC is projected to exceed the integrated HERA luminosity by two orders of magnitude. The physics programme is devoted to an exploration of the energy frontier, complementing the LHC and its discovery potential for physics beyond the Standard Model with high precision deep inelastic scattering measurements. These are designed to investigate a variety of fundamental questions in strong and electroweak interactions. The physics programme also includes electron-deuteron and electron-ion scattering in a $(Q^2, 1/x)$ range extended by four orders of magnitude as compared to previous lepton-nucleus DIS experiments for novel investigations of neutron's and nuclear structure, the initial conditions of Quark-Gluon Plasma formation and further quantum chromodynamic phenomena. The LHeC may be realised either as a ring-ring or as a linac-ring collider. Optics and beam dynamics studies are presented for both versions, along with technical design considerations on the interaction region, magnets and further components, together with a design study for a high acceptance detector. Civil engineering and installation studies are presented for the accelerator and the detector. The LHeC can be built within a decade and thus be operated while the LHC runs in its high-luminosity phase. It thus represents a major opportunity for progress in particle physics exploiting the investment made in the LHC.
The UA9 experimental equipment was installed in the CERN-SPS in March '09 with the aim of investigating crystal assisted collimation in coasting mode. Its basic layout comprises silicon bent crystals acting as primary collimators mounted inside two vacuum vessels. A movable 60 cm long block of tungsten located downstream at about 90 degrees phase advance intercepts the deflected beam. Scintillators, Gas Electron Multiplier chambers and other beam loss monitors measure nuclear loss rates induced by the interaction of the beam halo in the crystal. Roman pots are installed in the path of the deflected particles and are equipped with a Medipix detector to reconstruct the transverse distribution of the impinging beam. Finally UA9 takes advantage of an LHC-collimator prototype installed close to the Roman pot to help in setting the beam conditions and to analyze the efficiency to deflect the beam. This paper describes in details the hardware installed to study the crystal collimation during 2010.